BOARD
  ID = "DEL0029"
  NAME="Dell Powerline(TM) Workstation 466DE(TM) System Board"
  MFR="Dell Computer Corporation"
  CATEGORY = "SYS"
  SLOT = EMB(0)
  READID = YES
  SIZING = 0
  SYSTEM
    NONVOLATILE = 8192
    AMPERAGE = 20000
    SLOT(1) = EISA   LENGTH = 341 LABEL="EXP1"
    SLOT(2) = EISA   LENGTH = 341 LABEL="EXP2"
    SLOT(3) = EISA   LENGTH = 341 LABEL="EXP3"
    SLOT(4) = EISA   LENGTH = 341 LABEL="EXP4"
    SLOT(5) = EISA   LENGTH = 341 LABEL="EXP5"
    SLOT(6) = EISA   LENGTH = 341 LABEL="EXP6"
    MEMORY = 2048M  ADDRESS = 0  CACHE = YES  STEP = 32K

  ;--------------------------------
  ; Dell System Board Jumpers
  ;--------------------------------
JUMPER(1) = 1
  JTYPE = PAIRED
  NAME= "RSET"
  VERTICAL = YES
  LABEL = LOC(1) "RESET"
  INITVAL = LOC(1) 0
  FACTORY = LOC(1) 0
  COMMENTS = "Factory Reset Jumper\n
	      Jumper RSET is normally open (unjumpered).  Trained, qualified
 technicians can use this jumper to reset the system when it does not
 reboot normally or respond to the keyboard.  Do not install a jumper plug
 on the RSET pins unless instructed to do so by a Dell service technician."

  FUNCTION = "Factory Reset Jumper"
    SHOW = NO
    CHOICE = "Normal"

JUMPER(2) = 1
  JTYPE = PAIRED
  NAME = "MNT"
  VERTICAL = YES
  LABEL = LOC(1) "MNT"
  INITVAL = LOC(1) 0
  FACTORY = LOC(1) 0
  COMMENTS = "Factory Test Jumper\n
	      Jumper JM2 is used during the manufacture of the Dell System
 425E to test the basic input/output system (BIOS) software.  Thereafter,
 its pins are left open (unjumpered).  Do not install a jumper plug on the
 JM2 pins unless instructed to do so by a Dell service technician."

  FUNCTION = "Factory Test Jumper"
    SHOW = NO
    CHOICE = "Normal"

JUMPER(3) = 1
  JTYPE = PAIRED
  NAME = "BOOT"
  LABEL = LOC(1) "BOOT"
  VERTICAL = YES
  INITVAL =  LOC(1) 0
  FACTORY =  LOC(1) 0
  COMMENTS = "8K Boot Sector Jumper\n
              Install a jumper plug on jumper BOOT for erase/programming
              of the FLASH eprom."
  FUNCTION = "8K Boot Sector Jumper"
  SHOW = NO
  CHOICE = "Normal"

SWITCH(1) = 4
  STYPE = DIP
  NAME = "SW1"
  COMMENTS = "Switch SW1 contains four DIP switches.  See the switch positions listed below.\n
\n      OFF = UP = 0,    ON = DOWN = 1\n
\n  Switch Positions:
\n    1   -  1 = external VGA enabled
\n           0 = external VGA disabled
\n    2   -  1 = 90c11 multi-sync monitor attached
\n           0 = 90c11 multi-sync monitor not attached
\n    3   -  1 = Password lock enabled
\n           0 = Password lock disabled
\n    4   -  1 = JROM installed
\n           0 = flash eprom installed
\n"
  FACTORY = LOC(1-4) 0100
  VERTICAL = NO
  REVERSE = YES

  INCLUDE = "DELSETUP.OVL"

; For LIOWAIT we are actually initializing an indexed register (7b),
; but since the BIOS does a read before it writes register e4, the
; init statement below shows that we are initializing register 7A

GROUP = ""

  FUNCTION="BIOS Caching"
  COMMENTS="For better system performance, leave BIOS caching enabled unless
  	    told to disable it by a Dell service technician.\n"
    SHOW = EXP
    CHOICE="Enabled"
    FREE
      MEMORY=64k ADDRESS=0F0000h MEMTYPE=OTHER WRITABLE=NO CACHE=YES
    CHOICE="Disabled"
    FREE
      MEMORY=64k ADDRESS=0F0000h MEMTYPE=OTHER WRITABLE=NO CACHE=NO

  FUNCTION = "ISA Cycle Wait Control"
    TYPE = "LIOWAIT"
    SHOW = EXP
    COMMENTS= "This option sets the minimum time between back-to-back
               I/O cycles for ISA expansion cards."
    CHOICE = "420 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00110001
    CHOICE = "300 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00110000
    CHOICE = "540 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00110010
    CHOICE = "660 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00110011
    CHOICE = "780 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00110100
    CHOICE = "900 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00110101
    CHOICE = "1020 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00110110
    CHOICE = "1140 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00110111
    CHOICE = "1260 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00111000
    CHOICE = "1380 nanoseconds"
    LINK
    INIT = PORTADR(0e0h) BYTE 01111010
    INIT = PORTADR(0e4h) BYTE 00111001

  FUNCTION = "Fail-Safe Timer NMI"
    COMMENTS = "This option enables or disables the generation of a 
    		fail-safe timer non-maskable interrupt (NMI).\n"
    SHOW = EXP
    CHOICE = "Disabled"
      DISABLE=YES
      FREE
	INIT = PORTADR(0461h) BYTE rrrrr0rr
    CHOICE = "Enabled"
      FREE
	INIT = PORTADR(0461h) BYTE rrrrr1rr

  FUNCTION = "Bus-Master Timeout NMI"
    COMMENTS = "This option enables or disables the generation of a 
    		bus-master timeout non-maskable interrupt (NMI).\n"
    SHOW = EXP
    CHOICE = "Disabled"
      DISABLE=YES
      FREE
	INIT = PORTADR(0461h) BYTE rrrr0rrr
    CHOICE = "Enabled"
      FREE
	INIT = PORTADR(0461h) BYTE rrrr1rrr

  FUNCTION = "Software Generated NMI"
    COMMENTS = "This option enables or disables the generation of a 
    		software non-maskable interrupt (NMI).\n"
    SHOW = EXP
    CHOICE = "Disabled"
      DISABLE=YES
      FREE
	INIT = PORTADR(0461h) BYTE rrrrrr0r
    CHOICE = "Enabled"
      FREE
	INIT = PORTADR(0461h) BYTE rrrrrr1r

ENDGROUP