;
; (C)Copyright Hewlett-Packard Co., 1989-1990
;    All Rights Reserved.
;

BOARD
   ID       = "hwp1801"
   NAME     = "HP StarLAN 10 PC Link II (27240A)"
   MFR      = "Hewlett-Packard Co."
   CATEGORY = "NET"
   SLOT     = ISA8
   COMMENTS = "The HP StarLAN 10 PC adapter card is an IEEE 802.3 local area
               networking card for use with twisted-pair cabling."

SWITCH(1) = 4
   NAME = "I/O Base Address"
   STYPE = DIP
   REVERSE = YES
   FACTORY = LOC(4-1) 1001
   COMMENTS = "Switches 1 through 3 select the I/O Base Address,\n
               switch 4 is not applicable.\n
               NOTE: 'off' in the diagram below corresponds to
                     'OPEN' on card switches."

SWITCH(2) = 4
   NAME = "Loopback Mode"
   STYPE = DIP
   VERTICAL = YES
   FACTORY = LOC(1-4) 0000
   COMMENTS = "Switch 3 is the only switch in this bank that is used.
               It is accessible from the back plate of the card at
               the back of the computer.\n
               'N' is for Normal mode (when the interface card and network
               are operating normally).\n
               'T' is for Test mode (when you want to perform network
               diagnostic testing and troubleshooting).\n
               NOTE: 'off' in the diagram below corresponds to 'N' on the
                      card.\n
                     'on' corresponds to 'T'."





SOFTWARE(1) = "
 Your network software may ask you for this data:"

FUNCTION = "StarLAN 10 PC LAN Adapter (HP27240A)"
   TYPE = "NET"
   CONNECTION  = "One modular 8-pin LAN connector, and\n
                  one modular 6-pin phone connector"

   SUBFUNCTION = "I/O Base Address"
      CHOICE = "300h"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SWITCH(1) LOC(1-3) 100
            INIT = SOFTWARE(1) "I/O Base=300h"
            PORT = 300h
      CHOICE = "340h"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SWITCH(1) LOC(1-3) 110
            INIT = SOFTWARE(1) "I/O Base=340h"
            PORT = 340h
      CHOICE = "240h"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SWITCH(1) LOC(1-3) 001
            INIT = SOFTWARE(1) "I/O Base=240h"
            PORT = 240h
      CHOICE = "200h"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SWITCH(1) LOC(1-3) 000
            INIT = SOFTWARE(1) "I/O Base=200h"
            PORT = 200h
      CHOICE = "280h - Don't use with Novell Netware"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SWITCH(1) LOC(1-3) 010
            INIT = SOFTWARE(1) "I/O Base=280h"
            PORT = 280h
      CHOICE = "2C0h - Don't use with Novell Netware"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SWITCH(1) LOC(1-3) 011
            INIT = SOFTWARE(1) "I/O Base=2C0h"
            PORT = 2C0h
      CHOICE = "320h - Don't use with Novell Netware or HP Vectra CS"
         LINK
            INIT = SWITCH(1) LOC(4) 1
            INIT = SWITCH(1) LOC(1-3) 101
            INIT = SOFTWARE(1) "I/O Base=320h"
            PORT = 320h

   SUBFUNCTION = "Loopback Mode"
      CHOICE = "Normal operation"
         LINK
            INIT = SWITCH(2) LOC(3) 0
            INIT = SOFTWARE(1) "Loopback=normal"
      CHOICE = "Test mode"
         LINK
            INIT = SWITCH(2) LOC(3) 1
            INIT = SOFTWARE(1) "Loopback=test"

   SUBFUNCTION = "Interrupt Channel (IRQ)"
      CHOICE = "3"
         LINK
            INIT = Software(1) "IRQ=3"
            IRQ = 3
      CHOICE = "4"
         LINK
            INIT = Software(1) "IRQ=4"
            IRQ = 4
      CHOICE = "5"
         LINK
            INIT = Software(1) "IRQ=5"
            IRQ = 5
      CHOICE = "7"
         LINK
            INIT = Software(1) "IRQ=7"
            IRQ = 7