; $Header: c:/projects/util/overlay/ovl/v100/rcs/!hwp1950.cfg 1.1 1995/05/17 17:53:11 WKT00 Exp WKT00 $
; Hewlett-Packard 10/100VG ISA LAN Adapter (J2573A-80001)
; Configuration file version 2.12
; Overlay version: $Revision: 1.1 $
; !HWP1950.CFG  02/10/1995
;
; (C)Copyright Hewlett-Packard Co., 1993-1995
;    All Rights Reserved.
;

BOARD
   ID       = "HWP1950"
   NAME     = "HP 10/100VG Selectable ISA LAN Adapter (J2573A)"
   MFR      = "Hewlett-Packard Co."
   CATEGORY = "NET"
   SLOT     = ISA16
   LENGTH   = 220
   AMPERAGE = 90
   COMMENTS = "The HP 10/100VG Selectable ISA LAN Adapter is a 16-bit Type
	       10Base-T/100VG compatible local area networking adapter.\n\n
	       Your adapter configuration parameters of
	       IRQ, Memory Map Location and Boot ROM Location may be
	       chosen using this EISA configuration utility to match the
	       requirements of your computer. Your adapter also must be set to
	       match the values selected.  Use the program
	       HPVGSET.EXE to set your adapter configuration parameters.
	       HPVGSET.EXE is on the adapter's Support Disk."

SOFTWARE(1) = "
 The following configuration parameters have been selected
 for the HP 10/100VG Selectable ISA LAN Adapter.
 The HPVGSET.EXE program must be used to
 configure your adapter to match these values.
 Your network software also may ask you for this data:"

;
; I/O ports initialization Information Block
;
IOPORT(101) = PORTVAR(1)	; Base I/O ports address
	SIZE = BYTE
IOPORT(102) = PORTVAR(2)	; Page Reisgter
	SIZE = BYTE
IOPORT(103) = PORTVAR(3)	; IRQ Selection Register
	SIZE = BYTE
IOPORT(104) = PORTVAR(4)	; Memory-Mapped Address LSW
	SIZE = WORD
IOPORT(105) = PORTVAR(5)	; Memory-Mapped Address MSW
	SIZE = WORD
IOPORT(106) = PORTVAR(6)	; Boot ROM Configuration Register
	SIZE = WORD
IOPORT(107) = PORTVAR(7)	; Option Register LSW
	SIZE = WORD


FUNCTION = "HP 10/100VG Seletable ISA LAN Adapter (J2573A)"
   TYPE = "NET"
   CONNECTION  = "One modular RJ-45 LAN connector for 10Base-T network, and\n
                  one modular RJ-45 LAN connector for 100VG network"

   SUBFUNCTION = "I/O Address Range"

      CHOICE = "300h - 31Fh (Factory Default)"
	PORTVAR(1) = 300h
	PORTVAR(2) = 302h
	PORTVAR(3) = 30Dh
	PORTVAR(4) = 308h
	PORTVAR(5) = 30Ah
	PORTVAR(6) = 30Ah
	PORTVAR(7) = 304h
	LINK
	    PORT = 300h-31Fh
	    INIT = SOFTWARE(1) "I/O Ports 300h-31Fh"

      CHOICE = "100h - 11Fh"
	PORTVAR(1) = 100h
	PORTVAR(2) = 102h
	PORTVAR(3) = 10Dh
	PORTVAR(4) = 108h
	PORTVAR(5) = 10Ah
	PORTVAR(6) = 10Ah
	PORTVAR(7) = 104h
	LINK
	    PORT = 100h-11Fh
	    INIT = SOFTWARE(1) "I/O Ports 100h-11Fh"

      CHOICE = "140h - 15Fh"
	PORTVAR(1) = 140h
	PORTVAR(2) = 142h
	PORTVAR(3) = 14Dh
	PORTVAR(4) = 148h
	PORTVAR(5) = 14Ah
	PORTVAR(6) = 14Ah
	PORTVAR(7) = 144h
	LINK
	    PORT = 140h-15Fh
	    INIT = SOFTWARE(1) "I/O Ports 140h-15Fh"

      CHOICE = "180h - 19Fh"
	PORTVAR(1) = 180h
	PORTVAR(2) = 182h
	PORTVAR(3) = 18Dh
	PORTVAR(4) = 188h
	PORTVAR(5) = 18Ah
	PORTVAR(6) = 18Ah
	PORTVAR(7) = 184h
	LINK
	    PORT = 180h-19Fh
	    INIT = SOFTWARE(1) "I/O Ports 180h-19Fh"

      CHOICE = "1C0h - 1DFh"
	PORTVAR(1) = 1C0h
	PORTVAR(2) = 1C2h
	PORTVAR(3) = 1CDh
	PORTVAR(4) = 1C8h
	PORTVAR(5) = 1CAh
	PORTVAR(6) = 1CAh
	PORTVAR(7) = 1C4h
	LINK
	    PORT = 1C0h-1DFh
	    INIT = SOFTWARE(1) "I/O Ports 1C0h-1DFh"

      CHOICE = "200h - 21Fh"
	PORTVAR(1) = 200h
	PORTVAR(2) = 202h
	PORTVAR(3) = 20Dh
	PORTVAR(4) = 208h
	PORTVAR(5) = 20Ah
	PORTVAR(6) = 20Ah
	PORTVAR(7) = 204h
	LINK
	    PORT = 200h-21Fh
	    INIT = SOFTWARE(1) "I/O Ports 200h-21Fh"

      CHOICE = "240h - 25Fh"
	PORTVAR(1) = 240h
	PORTVAR(2) = 242h
	PORTVAR(3) = 24Dh
	PORTVAR(4) = 248h
	PORTVAR(5) = 24Ah
	PORTVAR(6) = 24Ah
	PORTVAR(7) = 244h
	LINK
	    PORT = 240h-25Fh
	    INIT = SOFTWARE(1) "I/O Ports 240h-25Fh"

      CHOICE = "280h - 29Fh"
	PORTVAR(1) = 280h
	PORTVAR(2) = 282h
	PORTVAR(3) = 28Dh
	PORTVAR(4) = 288h
	PORTVAR(5) = 28Ah
	PORTVAR(6) = 28Ah
	PORTVAR(7) = 284h
	LINK
	    PORT = 280h-29Fh
	    INIT = SOFTWARE(1) "I/O Ports 280h-29Fh"

      CHOICE = "2C0h - 2DFh"
	PORTVAR(1) = 2C0h
	PORTVAR(2) = 2C2h
	PORTVAR(3) = 2CDh
	PORTVAR(4) = 2C8h
	PORTVAR(5) = 2CAh
	PORTVAR(6) = 2CAh
	PORTVAR(7) = 2C4h
	LINK
	    PORT = 2C0h-2DFh
	    INIT = SOFTWARE(1) "I/O Ports 2C0h-2DFh"

      CHOICE = "340h - 35Fh"
	PORTVAR(1) = 340h
	PORTVAR(2) = 342h
	PORTVAR(3) = 34Dh
	PORTVAR(4) = 348h
	PORTVAR(5) = 34Ah
	PORTVAR(6) = 34Ah
	PORTVAR(7) = 344h
	LINK
	    PORT = 340h-35Fh
	    INIT = SOFTWARE(1) "I/O Ports 340h-35Fh"

      CHOICE = "380h - 39Fh"
	PORTVAR(1) = 380h
	PORTVAR(2) = 382h
	PORTVAR(3) = 38Dh
	PORTVAR(4) = 388h
	PORTVAR(5) = 38Ah
	PORTVAR(6) = 38Ah
	PORTVAR(7) = 384h
	LINK
	    PORT = 380h-39Fh
	    INIT = SOFTWARE(1) "I/O Ports 380h-39Fh"

      CHOICE = "3C0h - 3DFh"
	PORTVAR(1) = 3C0h
	PORTVAR(2) = 3C2h
	PORTVAR(3) = 3CDh
	PORTVAR(4) = 3C8h
	PORTVAR(5) = 3CAh
	PORTVAR(6) = 3CAh
	PORTVAR(7) = 3C4h
	LINK
	    PORT = 3C0h-3DFh
	    INIT = SOFTWARE(1) "I/O Ports 3C0h-3DFh"

   SUBFUNCTION = "Interrupt Channel (IRQ)"

      CHOICE = "3 (Factory Default)"
	 LINK
	    IRQ = 3
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  3"

      CHOICE = "4"
	 LINK
	    IRQ = 4
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  4"

      CHOICE = "5"
	 LINK
	    IRQ = 5
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  5"

      CHOICE = "6"
	 LINK
	    IRQ = 6
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  6"

      CHOICE = "7"
	 LINK
	    IRQ = 7
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  7"

      CHOICE = "9"
	 LINK
	    IRQ = 9
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  9"

      CHOICE = "10"
	 LINK
	    IRQ = 10
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  10"

      CHOICE = "11"
	 LINK
	    IRQ = 11
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  11"

      CHOICE = "12"
	 LINK
	    IRQ = 12
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  12"

      CHOICE = "15"
	 LINK
	    IRQ = 15
	    SHARE = NO
	    TRIGGER = EDGE
	    INIT = Software(1) "IRQ  15"

   SUBFUNCTION = "Memory-Mapped I/O"
	HELP = "The memory-mapped I/O may be utilized by high performance
		network drivers, consult your network driver documentation.\n\n
		It is OK if the memory address selected overlaps the address
		used for a boot ROM on the same adapter, but overlap is not
		allowed by this EISA utility. A conflict notice occurs.
		If address overlap exists, use the
		EISA utility to enable the boot ROM at the address and disable
		memory-mapped I/O. Then, enable both boot ROM and
		memory-mapped I/O
		using the adapter's HPVGSET.EXE program.\n"
	CHOICE = "DISABLE"
		DISABLE = YES
		LINK
			INIT = Software(1) "MEM MAP DISABLED"
	CHOICE = "C8000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0C8000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at C8000h"

	CHOICE = "CC000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0CC000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at CC000h"

	CHOICE = "D0000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0D0000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at D0000h"

	CHOICE = "D4000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0D4000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at D4000h"

	CHOICE = "D8000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0D8000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at D8000h"

	CHOICE = "DC000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0DC000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at DC000h"

	CHOICE = "E0000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0E0000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at E0000h"

	CHOICE = "E4000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0E4000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at E4000h"

	CHOICE = "E8000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0E8000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at E8000h"

	CHOICE = "EC000h"
		LINK
			MEMORY = 8192
			ADDRESS = 0EC000h
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "MEM MAP at EC000h"

       CHOICE = "Above 1 Meg, auto select"
	 HELP = "The 'Above 1 Meg, auto select' choice will select an address
		above the end of installed memory. Select Options -
		Auto Verify for this automatic selection to be made.
		Then select View - Resources to view the address selected.
		Note this address and set this address on the adapter
		using HPVGSET.EXE."
		LINK
			MEMORY = 8192
			INIT = Software(1) "MEM MAP above 1 Meg"
			ADDRESS = 0100000h - 0FFFE00h STEP = 8192
			WRITABLE = YES
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO

   SUBFUNCTION = "Boot ROM"
	HELP = " A boot ROM may be installed to allow system boot from a
		network server.\n\n
		It is OK if the boot ROM address selected overlaps the
		address used for memory-mapped I/O on the same adapter,
		but overlap is not allowed by this EISA utility. A conflict
		notice occurs. If address overlap exists, use the
		EISA utility to enable the boot ROM at the address and disable
		memory-mapped I/O. Then, enable both boot ROM and
		memory-mapped I/O using the adapter's HPVGSET.EXE program.\n"

	CHOICE = "DISABLE"
		DISABLE = YES
		LINK
			INIT = Software(1) "BOOT ROM DISABLED"

	CHOICE = "8K at C000h"
	    FREE
		MEMORY = 8K
		ADDRESS = 0C0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "8K BOOT ROM at C0000h"

	CHOICE = "8K at D000h"
	    FREE
		MEMORY = 8K
		ADDRESS = 0D0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "8K BOOT ROM at D0000h"

	CHOICE = "8K at E000h"
	    FREE
		MEMORY = 8K
		ADDRESS = 0E0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "8K BOOT ROM at E0000h"

	CHOICE = "12K at C000h"
	    FREE
		MEMORY = 12K
		ADDRESS = 0C0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "12K BOOT ROM at C0000h"

	CHOICE = "12K at D000h"
	    FREE
		MEMORY = 12K
		ADDRESS = 0D0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "12K BOOT ROM at D0000h"

	CHOICE = "12K at E000h"
	    FREE
		MEMORY = 12K
		ADDRESS = 0E0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "12K BOOT ROM at E0000h"

	CHOICE = "16K at C000h"
	    FREE
		MEMORY = 16K
		ADDRESS = 0C0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "16K BOOT ROM at C0000h"

	CHOICE = "16K at D000h"
	    FREE
		MEMORY = 16K
		ADDRESS = 0D0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "16K BOOT ROM at D0000h"

	CHOICE = "16K at E000h"
	    FREE
		MEMORY = 16K
		ADDRESS = 0E0000h
			WRITABLE = NO
			MEMTYPE = OTH
			SIZE = WORD
			CACHE = NO
			SHARE = NO
			INIT = Software(1) "16K BOOT ROM at E0000h"