BOARD ID="INT30F1" NAME="HP NetServer LM System Board" MFR="Hewlett-Packard Co." CATEGORY="SYS" SLOT=EMB(0) READID=YES COMMENTS="This is the HP NetServer LM System Board with 9 EISA expansion slots. This system board contains the following on-board features:\n \t1) Static RAM Cache,\n \t2) Shadow RAM Control,\n \t3) Paged Memory,\n \t4) 1 Parallel Port,\n \t5) 2 Serial Ports,\n \t6) Onboard Video Controller,\n \t7) Onboard Floppy Controller,\n \t8) Onboard IDE Hard Disk Controller,\n \t9) Embedded EISA Busmaster SCSI Adapter,\n \t10) Onboard mouse/keyboard interface." HELP="This is the base module configuration options file. The user should review and configure selectable options per system resources." SYSTEM NONVOLATILE = 8K AMPERAGE = 12000 SLOT(1) = EISA LENGTH = 341 BUSMASTER = YES SLOT(2) = EISA LENGTH = 341 BUSMASTER = YES SLOT(3) = EISA LENGTH = 341 BUSMASTER = YES SLOT(4) = EISA LENGTH = 341 BUSMASTER = YES SLOT(5) = EISA LENGTH = 341 BUSMASTER = YES SLOT(6) = EISA LENGTH = 341 BUSMASTER = YES SLOT(7) = EISA LENGTH = 341 BUSMASTER = YES SLOT(8) = EISA LENGTH = 341 BUSMASTER = YES SLOT(9) = EISA LENGTH = 341 BUSMASTER = YES MEMORY=640K ADDRESS=0K CACHE=YES STEP=32K MEMORY=128K ADDRESS=0A0000h CACHE=NO MEMORY=32K ADDRESS=0C0000h CACHE=YES STEP=32K MEMORY=96K ADDRESS=0C8000h CACHE=YES STEP=32K MEMORY=128K ADDRESS=0E0000h CACHE=YES STEP=32K MEMORY=255M ADDRESS=1M CACHE=YES STEP=32K IOPORT(1) = 0zC02h SIZE = BYTE INITVAL = rrrrxrrr IOPORT(2)=09c5ch ;Interrupt definition INITVAL = X000XXXX IOPORT(3)=09c84h ;Interrupt definition INITVAL = rrrrrrrX ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; JUMPER(1) = 2 NAME = "FLASH - E0191" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(1^2) "Boot" FACTORY = LOC(1^2 2^3) 10 INITVAL = LOC(1^2 2^3) 10 COMMENTS = "Move this jumper to the recovery position (pins 2 to 3) to enable the system recovery BIOS. The recovery BIOS must be used with the FLASH Update Utility to restore a corrupted system BIOS. During normal operation, this jumper must be in the BOOT position (pins 1 to 2)." JUMPER(2) = 2 NAME = "VGA - E0290" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(1^2) "ON" FACTORY = LOC(1^2 2^3) 10 COMMENTS = "Move this jumper to the off position (pins 2 to 3) to disable the onboard video controller. When an external video controller is present, the onboard controller should be disabled. Leave this jumper in the ON position (pins 1 to 2) to enable the onboard video controller." JUMPER(3) = 2 NAME = "NVRAM - E0292" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(2^3) "CLR" FACTORY = LOC(1^2 2^3) 10 INITVAL = LOC(1^2 2^3) 10 COMMENTS = "Move this jumper to the CLR position (pins 2 to 3) to clear the present contents of EISA NVRAM and ISA CMOS. System defaults will be installed. During normal operation, the jumper should be in the normal position (pins 1 to 2)." JUMPER(4) = 2 NAME = "PASSWORD - E0390" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(2^3) "OFF" FACTORY = LOC(1^2 2^3) 10 INITVAL = LOC(1^2 2^3) 10 COMMENTS = "Move jumper to the on position (pins 1 to 2) to enable use of the power-on password. The OFF position (pins 2 to 3) clears the system password. The on position enables use of the power-on password." JUMPER(5) = 2 NAME = "FLASH - E0721" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(2^3) "F-P" FACTORY = LOC(1^2 2^3) 10 INITVAL = LOC(1^2 2^3) 10 COMMENTS = "Move this jumper to the enabled position (pins 1 to 2) to allow the user to update FLASH memory with new BIOS or configuration information. This jumper must be in this position for the ECU to save the defined configuration or for ROM based setup to update the user definable hard disk types. Place this jumper in the F-P position (pins 2 to 3) to prevent FLASH updates and configuration changes." JUMPER(6) = 2 NAME = "Floppy - E0291" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(1^2) "R/W" FACTORY = LOC(1^2 2^3) 10 INITVAL = LOC(1^2 2^3) 10 COMMENTS = "Move this jumper to the write protected position (pins 2 to 3) to prevent writes to the floppy drive. This jumper should be in the R/W position (pins 1 to 2) when writes to the floppy drive are to be allowed." JUMPER(7) = 2 NAME = "SIMM0 - E0391" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(1^2) "STD" FACTORY = LOC(1^2 2^3) 10 INITVAL = LOC(1^2 2^3) 10 COMMENTS = "See your User's Guide for information on setting the SIMM size jumpers." JUMPER(8) = 2 NAME = "SIMM1 - E0392" JTYPE = INLINE VERTICAL = NO REVERSE = YES LABEL = LOC(1^2) "STD" FACTORY = LOC(1^2 2^3) 10 INITVAL = LOC(1^2 2^3) 10 COMMENTS = "See your User's Guide for information on setting the SIMM size jumpers." ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; include the configuraton file extension (overlay) INCLUDE = "INT30F1.OVL" ;Line 175 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ;******* ;; ADVANCED FUNCTIONS ;; The functions with SHOW=EXP are displayed in the ECU only when the ;; \A option is given on ECU startup (SD.EXE /A) or when is entered ;; at the "Welcome" screen of the system dispatcher (SD.EXE). ;******* FUNCTION = "Slot 4 AEN Control" SHOW = EXP HELP = "This function allows the user to select the operation of slot 4. When slot 4 is set to EISA compatible, then it will implement the geographical addressing scheme of EISA. When set to ISA compatible, all I/O accesses will be permitted to that slot. This is required for any add-in boards that are addressed in the range 0-255." CHOICE = "EISA Compatible" FREE INIT = IOPORT(1) LOC(3) 0 CHOICE = "ISA Compatible" FREE INIT = IOPORT(1) LOC(3) 1 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; static system resources that are not available for add-in cards. ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; FUNCTION = "Reserved System Resources" TYPE = "HP_PC,NAME=NETSERVER LM,SPU_NUM=36" HELP = "This function defines system resources that are reserved and not available for expansion boards. These resources are interrupts and port ranges used by the system board." CHOICE = "Configuration File and Overlay Version 2.7 HP" FREE MEMORY=16K ADDRESS=0E8000h MEMTYPE=OTH WRITABLE=YES CACHE=NO MEMORY=64K ADDRESS=0F0000h MEMTYPE=OTH WRITABLE=NO CACHE=YES FREE IRQ = 0 TRIGGER=EDGE SHARE=NO IRQ = 1 TRIGGER=EDGE SHARE=NO IRQ = 13 TRIGGER=EDGE SHARE=NO