;                                                              
;  ALTServer Premium System Board
;
BOARD
  ID="INT31A0"
  NAME="System Board"
  MFR="Intel"
  CATEGORY="SYS"
  SLOT=EMB(0)
  READID=YES
  COMMENTS="This system board contains the following on-board features:\n
            \t1)  2 CPU ZIF sockets supporting up to\n
                 \t\t2 processors,\n
            \t2)  8 Parity Memory connectors\n
            \t3)  3 PCI connectors,\n
            \t4)  6 EISA connectors,\n
            \t5)  Static RAM Cache,\n
            \t6)  Shadow RAM Control,\n
            \t7)  Paged Memory,\n
            \t8)  1 Parallel Port,\n
            \t9)  2 Serial Ports,\n
            \t10) Onboard PCI Video Controller,\n
            \t11) Onboard Floppy Controller,\n
            \t12) Onboard IDE Hard Disk Controller,\n
            \t13) Onboard mouse/keyboard interface.\n
            \t14) Onboard PCI SCSI Controller.\n"
HELP="This is the base module configuration options file.  The user
      should review and configure selectable options per system resources."

SYSTEM
  NONVOLATILE = 8K                               
  AMPERAGE = 12000
  SLOT(1)  = EISA  LENGTH = 341 BUSMASTER = YES
  SLOT(2)  = EISA  LENGTH = 341 BUSMASTER = YES
  SLOT(3)  = EISA  LENGTH = 341 BUSMASTER = YES
  SLOT(4)  = EISA  LENGTH = 341 BUSMASTER = YES
  SLOT(5)  = EISA  LENGTH = 341 BUSMASTER = YES
  SLOT(6)  = EISA  LENGTH = 341 BUSMASTER = YES

  MEMORY=640K  ADDRESS=0K      CACHE=YES
    STEP=16K

  MEMORY=384K  ADDRESS=0A0000h CACHE=YES
    STEP=16K

  MEMORY=4095M ADDRESS=1M      CACHE=YES
    STEP=1M

IOPORT(1)       = 0zC02h
	SIZE    = BYTE
	INITVAL = rrrrxrrr
IOPORT(2)=09c5ch                        ;Interrupt definition
	INITVAL = X000XXXX                                      

IOPORT(3)=09c84h                        ;Interrupt definition
	INITVAL = rrrrrrrX                                      

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; include the configuraton file extension (overlay)

INCLUDE = "INT31A0.OVL"
; line 177
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

GROUP = "Reserved System Resources"
FUNCTION = "Reserved EISA ID Ports"
TYPE = "EISAIDP"
SHOW = NO
  CHOICE = "EISA ID ports"
    FREE
    PORT = 0C80H-0C83H                  ; Reserve EISA ID ports
    PORT = 01C80H-01C83H
    PORT = 02C80H-02C83H
    PORT = 03C80H-03C83H
    PORT = 04C80H-04C83H
    PORT = 05C80H-05C83H
    PORT = 06C80H-06C83H

FUNCTION = "Reserve ISA PIC ports"
TYPE = "ISAPP"
SHOW = NO
  CHOICE = "ISA PIC ports"
  FREE
    PORT = 020H-021H
    PORT = 0A0H-0A1H

FUNCTION = "Reserve EISA DMA ports"
TYPE = "EISADMAP"
SHOW = NO
  CHOICE = "EISA DMA ports"
  FREE
    DMA = 4
    PORT = 0H-0FH
    PORT = 80H-90H
    PORT = 94H-9FH
    PORT = 0C0H-0DEH
    PORT = 040BH
    PORT = 0410H-043FH
    PORT = 0481H-0483H
    PORT = 0487H
    PORT = 0489H-048CH
    PORT = 04D6H

FUNCTION = "Reserve Timer ports"
TYPE = "TIMERP"
SHOW = NO
  CHOICE = "Timer ports"
  FREE
    IRQ = 0
    PORT = 040H-043H

FUNCTION = "Reserve Real Time Clock ports"
TYPE = "RTCP"
SHOW = NO
  CHOICE = "RTC ports"
  FREE
    IRQ = 8
    PORT = 070H-071H

FUNCTION = "Reserve Speaker ports"
TYPE = "SPKP"
SHOW = NO
  CHOICE = "Speaker ports"
  FREE
    PORT = 061H

FUNCTION = "Reserve Math Co-processor ports"
TYPE = "MCP"
SHOW = NO
  CHOICE = "Math Co-processor ports"
  FREE
    IRQ = 13
    PORT = 0F0H-0FFH

FUNCTION = "Reserve Keyboard Controller ports"
TYPE = "KCP"
SHOW = NO
  CHOICE = "Keyboard Controller ports"
  FREE
    IRQ = 1
    PORT = 060H
    PORT = 064H

FUNCTION = "Reserve SYSTEM Memory"
TYPE = "SYSME"
SHOW = NO
  SUBFUNCTION = "MEM AT 0E8000H"
    CHOICE = "Memory AT 0E8000"
    FREE
      MEMORY = 96K
        ADDRESS=0E8000H
        MEMTYPE=OTH
        WRITABLE=NO
        CACHE=YES

  SUBFUNCTION = "MEM AT 0FFF80000H"
    CHOICE = "Memory AT 0FFF80000"
    FREE
      MEMORY = 512K
        ADDRESS=0FFF80000H
        MEMTYPE=OTH
        WRITABLE=NO
        CACHE=YES

FUNCTION = "Reserve P54C Memory"
TYPE = "P54M"
SHOW = NO
  CHOICE = "P54C Memory"
  FREE
    MEMORY = 4K
      ADDRESS=0FEE00000H
      MEMTYPE=OTH
      CACHE=YES

FUNCTION = "Reserve IC2 ports"
TYPE = "IC2P"
SHOW = NO
  CHOICE = "IC2 ports"
  FREE
    PORT = 0CA0H-0CA1H

ENDGROUP


;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;; Switch and Jumper declarations
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

JUMPER(1)       = 2
NAME            = "J1A & J1B"
JTYPE           = TRIPOLE
VERTICAL        = YES
REVERSE         = YES
LABEL           = LOC(2-1) "J1A" "J1B"
FACTORY         = LOC(2-1) 00
COMMENTS        =
"CPU ³J1A³J2A³J5B³J6B³ Bus³ B:C º CPU ³J1A³J2A³J5B³J6B³ Bus³ B:C\n
 75  ³>0<³ 0 ³ 0 ³ 1 ³ 50 ³ 2:3 º 133 ³>0<³ 1 ³ 1 ³ 1 ³ 66 ³ 1:2\n
 90  ³>0<³ 0 ³ 0 ³ 0 ³ 60 ³ 2:3 º 150 ³>1<³ 0 ³ 0 ³ 1 ³ 50 ³ 1:3\n
 100 ³>0<³ 1 ³ 0 ³ 1 ³ 50 ³ 1:2 º 150*³>1<³ 1 ³ 0 ³ 0 ³ 60 ³ 2:5\n
 100 ³>0<³ 0 ³ 1 ³ 1 ³ 66 ³ 2:3 º 166*³>1<³ 1 ³ 1 ³ 1 ³ 66 ³ 2:5\n
 120 ³>0<³ 1 ³ 0 ³ 0 ³ 60 ³ 1:2 º 180 ³>1<³ 0 ³ 0 ³ 0 ³ 60 ³ 1:3\n
 125*³>1<³ 1 ³ 0 ³ 1 ³ 50 ³ 2:5 º 200 ³>1<³ 0 ³ 1 ³ 1 ³ 66 ³ 1:3\n
 * Not all CPU steppings support 2:5 Bus:Core (B:C) Ratio\n
\tJ1B = CMOS/NVRAM Clear\n
\t\tPosition 0 = Protect\n
\t\tPosition 1 = Erase/Program\n"
HELP            =
"This display is information only.\n  
Please refer to the System Board\n
documentation for specific infor-\n
mation on correct jumper settings.\n"

JUMPER(2)       = 2
NAME            = "J2A & J2B"
JTYPE           = TRIPOLE
VERTICAL        = YES
REVERSE         = YES
LABEL           = LOC(2-1) "J2A" "J2B"
FACTORY         = LOC(2-1) 00
COMMENTS        =
"CPU ³J1A³J2A³J5B³J6B³ Bus³ B:C º CPU ³J1A³J2A³J5B³J6B³ Bus³ B:C\n
 75  ³ 0 ³>0<³ 0 ³ 1 ³ 50 ³ 2:3 º 133 ³ 0 ³>1<³ 1 ³ 1 ³ 66 ³ 1:2\n
 90  ³ 0 ³>0<³ 0 ³ 0 ³ 60 ³ 2:3 º 150 ³ 1 ³>0<³ 0 ³ 1 ³ 50 ³ 1:3\n
 100 ³ 0 ³>1<³ 0 ³ 1 ³ 50 ³ 1:2 º 150*³ 1 ³>1<³ 0 ³ 0 ³ 60 ³ 2:5\n
 100 ³ 0 ³>0<³ 1 ³ 1 ³ 66 ³ 2:3 º 166*³ 1 ³>1<³ 1 ³ 1 ³ 66 ³ 2:5\n
 120 ³ 0 ³>1<³ 0 ³ 0 ³ 60 ³ 1:2 º 180 ³ 1 ³>0<³ 0 ³ 0 ³ 60 ³ 1:3\n
 125*³ 1 ³>1<³ 0 ³ 1 ³ 50 ³ 2:5 º 200 ³ 1 ³>0<³ 1 ³ 1 ³ 66 ³ 1:3\n
 * Not all CPU steppings support 2:5 Bus:Core (B:C) Ratio\n
\tJ2B = Password Clear\n
\t\tPosition 0 = Protect\n
\t\tPosition 1 = Erase/Program\n"
HELP            =
"This display is information only.\n  
Please refer to the System Board\n
documentation for specific infor-\n
mation on correct jumper settings.\n"

JUMPER(3)       = 2
NAME            = "J3A & J3B"
JTYPE           = TRIPOLE
VERTICAL        = YES
REVERSE         = YES
LABEL           = LOC(2-1) "J3A" "J3B"
FACTORY         = LOC(2-1) 00
COMMENTS        =
"\tJ3A = Voltage Set\n
\t\tPosition 0 = VRE\n
\t\tPosition 1 = N/A\n
\tJ3B = CPU Type\n
\t\tPosition 0 = CPU1 (R) Primary\n
\t\tPosition 1 = CPU2 (L) Primary\n"
HELP            =
"This display is information only.\n  
Please refer to the System Board\n
documentation for specific infor-\n
mation on correct jumper settings.\n"

JUMPER(4)       = 2
NAME            = "J4A & J4B"
JTYPE           = TRIPOLE
VERTICAL        = YES
REVERSE         = YES
LABEL           = LOC(2-1) "J4A" "J4B"
FACTORY         = LOC(2-1) 00
COMMENTS        =
"\tJ4A = Color\n
\t\tPosition 0 = Color\n
\t\tPosition 1 = Mono\n
\tJ4B = Kick Start\n
\t\tPosition 0 = Disable\n
\t\tPosition 1 = Enable\n"
HELP            =
"This display is information only.\n  
Please refer to the System Board\n
documentation for specific infor-\n
mation on correct jumper settings.\n"

JUMPER(5)       = 2
NAME            = "J5A & J5B"
JTYPE           = TRIPOLE
VERTICAL        = YES
REVERSE         = YES
LABEL           = LOC(2-1) "J5A" "J5B"
FACTORY         = LOC(2-1) 00
COMMENTS        =
"\tJ5A = Boot Block\n
\t\tPosition 0 = Protected\n
\t\tPosition 1 = Erase/Program\n
CPU ³J1A³J2A³J5B³J6B³ Bus³ B:C º CPU ³J1A³J2A³J5B³J6B³ Bus³ B:C\n
75  ³ 0 ³ 0 ³>0<³ 1 ³ 50 ³ 2:3 º 133 ³ 0 ³ 1 ³>1<³ 1 ³ 66 ³ 1:2\n
90  ³ 0 ³ 0 ³>0<³ 0 ³ 60 ³ 2:3 º 150 ³ 1 ³ 0 ³>0<³ 1 ³ 50 ³ 1:3\n
100 ³ 0 ³ 1 ³>0<³ 1 ³ 50 ³ 1:2 º 150*³ 1 ³ 1 ³>0<³ 0 ³ 60 ³ 2:5\n
100 ³ 0 ³ 0 ³>1<³ 1 ³ 66 ³ 2:3 º 166*³ 1 ³ 1 ³>1<³ 1 ³ 66 ³ 2:5\n
120 ³ 0 ³ 1 ³>0<³ 0 ³ 60 ³ 1:2 º 180 ³ 1 ³ 0 ³>0<³ 0 ³ 60 ³ 1:3\n
125*³ 1 ³ 1 ³>0<³ 1 ³ 50 ³ 2:5 º 200 ³ 1 ³ 0 ³>1<³ 1 ³ 66 ³ 1:3\n
* Not all CPU steppings support 2:5 Bus:Core (B:C) Ratio\n"
HELP            =
"This display is information only.\n  
Please refer to the System Board\n
documentation for specific infor-\n
mation on correct jumper settings.\n"

JUMPER(6)       = 2
NAME            = "J6A & J6B"
JTYPE           = TRIPOLE
VERTICAL        = YES
REVERSE         = YES
LABEL           = LOC(2-1) "J6A" "J6B"
FACTORY         = LOC(2-1) 00
COMMENTS        =
"\tJ6A = Flash Code\n
\t\tPosition 0 = Erase/Program\n
\t\tPosition 1 = Protect\n
CPU ³J1A³J2A³J5B³J6B³ Bus³ B:C º CPU ³J1A³J2A³J5B³J6B³ Bus³ B:C\n
75  ³ 0 ³ 0 ³ 0 ³>1<³ 50 ³ 2:3 º 133 ³ 0 ³ 1 ³ 1 ³>1<³ 66 ³ 1:2\n
90  ³ 0 ³ 0 ³ 0 ³>0<³ 60 ³ 2:3 º 150 ³ 1 ³ 0 ³ 0 ³>1<³ 50 ³ 1:3\n
100 ³ 0 ³ 1 ³ 0 ³>1<³ 50 ³ 1:2 º 150*³ 1 ³ 1 ³ 0 ³>0<³ 60 ³ 2:5\n
100 ³ 0 ³ 0 ³ 1 ³>1<³ 66 ³ 2:3 º 166*³ 1 ³ 1 ³ 1 ³>1<³ 66 ³ 2:5\n
120 ³ 0 ³ 1 ³ 0 ³>0<³ 60 ³ 1:2 º 180 ³ 1 ³ 0 ³ 0 ³>0<³ 60 ³ 1:3\n
125*³ 1 ³ 1 ³ 0 ³>1<³ 50 ³ 2:5 º 200 ³ 1 ³ 0 ³ 1 ³>1<³ 66 ³ 1:3\n
* Not all CPU steppings support 2:5 Bus:Core (B:C) Ratio\n"
HELP            =
"This display is information only.\n  
Please refer to the System Board\n
documentation for specific infor-\n
mation on correct jumper settings.\n"

JUMPER(7)       = 2
NAME            = "J7A & J7B"
JTYPE           = TRIPOLE
VERTICAL        = YES
REVERSE         = YES
LABEL           = LOC(2-1) "J7A" "J7B"
FACTORY         = LOC(2-1) 00
COMMENTS        =
"\tJ7A = Boot Option\n
\t\tPosition 0 = Normal Boot\n
\t\tPosition 1 = Recovery Boot\n
\tJ7B = Option 1\n
\t\tPosition 0 = High\n
\t\tPosition 1 = Low\n"
HELP            =
"This display is information only.\n  
Please refer to the System Board\n
documentation for specific infor-\n
mation on correct jumper settings.\n"