BOARD ; 11/17 fcm Chg; 06/91 dmw Chg ID="ISA8C04" NAME="3COM 3C603 Tokenlink 16bit" MFR="3COM" CATEGORY="NET" SLOT=ISA16 LENGTH=336 COMMENTS=" \nSelect desired Network Operating System or General Use to obtain valid hardware options. \n\nBe sure the switch settings are correct and the card is in a 16bit slot or it will not work. \n\nNote: IRQ 2 is equivalent to IRQ 9. " JUMPER(1)=4 JTYPE=paired NAME="I/O" REVERSE=YES LABEL=LOC(1-4) "300" "310" "330" "350" JUMPER(2)=4 JTYPE=paired NAME="MEM" REVERSE=YES LABEL=LOC(1-4) "OFF" "C4000" "C6000" "D4000" FACTORY=LOC(1-4) 1000 JUMPER(3)=3 JTYPE=paired NAME="INTLVL" REVERSE=YES LABEL=LOC(1-3) "PRI" "SEC" "OFF" FACTORY=LOC(1-3) 001 JUMPER(4)=8 JTYPE=paired NAME="DMA CHANNELS" LABEL=LOC(8-1) "7" " " "6" " " "5" " " "3" " " FACTORY=LOC(8-1) 00000011 JUMPER(5)=6 JTYPE=paired NAME="INTERRUPTS" LABEL=LOC(6-1) "15" "14" "12" "11" "10" "5" FACTORY=LOC(6-1) 000001 SOFTWARE(1)=" Add Command Line Parameters to Device Drivers and 3COMREUI (TOKREUI Substitute) as follows: \n\tDEVICE=TOK603.sys x y z\t\t3+Plus \n\tDEVICE=3COMAH.SYS x y z\t\tPC LAN \n\t3COMREUI x, y, z \n\nX,Y and Z are the parameters for IRQ, DMA and PORT address settings,and must be set to the appropriate value, shown below...\n" FUNCTION="3C603 Config Options" TYPE="NET" SUBFUNCTION="3+Plus or General Use" CHOICE="Adapter Options No Remote Boot" LINK IRQ= 9|3|4|5| 10|11|12|14|15 INIT=JUMPER(5) LOC(6-1) 000000|000000|000000|000001| 000010|000100|001000|010000|100000 INIT=software(1) "x=2"|"x=3"|"x=4"|"x=5"| "x=10"|"x=11"|"x=12"|"x=14"|"x=15" LINK DMA= 5|6|7|3 TIMING=TYPEA INIT=JUMPER(4) LOC(8-1) 00001100|00110000|11000000|00000011 INIT=software(1) "z=5"|"z=6"|"z=7"|"z=3" LINK PORT=300h-30Fh|310h-31Fh|330h-33Fh|350h-35Fh INIT=JUMPER(1) LOC(1-4) 1000|0100|0010|0001 INIT=software(1) "y=300h"|"y=310h"|"y=330h"|"y=350h" FREE INIT=JUMPER(2) LOC(1-4) 1000 CHOICE="Adapter Options Remote Boot" LINK IRQ= 9|3|4|5| 10|11|12|14|15 INIT=JUMPER(5) LOC(6-1) 000000|000000|000000|000001| 000010|000100|001000|010000|100000 INIT=software(1) "x=2"|"x=3"|"x=4"|"x=5"| "x=10"|"x=11"|"x=12"|"x=14"|"x=15" LINK DMA= 5|6|7|3 TIMING=TYPEA INIT=JUMPER(4) LOC(8-1) 00001100|00110000|11000000|00000011 INIT=software(1) "z=5"|"z=6"|"z=7"|"z=3" LINK PORT=300h-30Fh|310h-31Fh|330h-33Fh|350h-35Fh INIT=JUMPER(1) LOC(1-4) 1000|0100|0010|0001 INIT=software(1) "y=300h"|"y=310h"|"y=330h"|"y=350h" COMBINE MEMORY=8K ADDRESS=0C4000h|0C6000h|0D4000h MEMTYPE=OTH INIT=JUMPER(2) LOC(1-4) 0100|0010|0001 CHOICE="Not Selected" SUBFUNCTION="Banyan VINES" CHOICE="Not Selected" CHOICE="Adapter Options No Remote Boot" LINK IRQ= 9|3|4|5| 10|11|12|14|15 INIT=JUMPER(5) LOC(6-1) 000000|000000|000000|000001| 000010|000100|001000|010000|100000 INIT=software(1) "x=2"|"x=3"|"x=4"|"x=5"| "x=10"|"x=11"|"x=12"|"x=14"|"x=15" LINK DMA= 5|6|7|3 TIMING=TYPEA INIT=JUMPER(4) LOC(8-1) 00001100|00110000|11000000|00000011 INIT=software(1) "z=5"|"z=6"|"z=7"|"z=3" LINK PORT=300h-30Fh|310h-31Fh|330h-33Fh|350h-35Fh INIT=JUMPER(1) LOC(1-4) 1000|0100|0010|0001 INIT=software(1) "y=300h"|"y=310h"|"y=330h"|"y=350h" FREE INIT=JUMPER(2) LOC(1-4) 1000 CHOICE="Adapter Options Remote Boot" LINK IRQ= 9|3|4|5| 10|11|12|14|15 INIT=JUMPER(5) LOC(6-1) 000000|000000|000000|000001| 000010|000100|001000|010000|100000 INIT=software(1) "x=2"|"x=3"|"x=4"|"x=5"| "x=10"|"x=11"|"x=12"|"x=14"|"x=15" LINK DMA= 5|6|7|3 TIMING=TYPEA INIT=JUMPER(4) LOC(8-1) 00001100|00110000|11000000|00000011 INIT=software(1) "z=5"|"z=6"|"z=7"|"z=3" LINK PORT=300h-30Fh|310h-31Fh|330h-33Fh|350h-35Fh INIT=JUMPER(1) LOC(1-4) 1000|0100|0010|0001 INIT=software(1) "y=300h"|"y=310h"|"y=330h"|"y=350h" COMBINE MEMORY=8K ADDRESS=0C4000h|0C6000h|0D4000h MEMTYPE=OTH INIT=JUMPER(2) LOC(1-4) 0100|0010|0001 FUNCTION="INTLVL Register" CHOICE="Primary Position" LINK PORT=0A20h INIT=JUMPER(3) LOC(1-3) 100 CHOICE="Secondary Position" LINK PORT=0A24h INIT=JUMPER(3) LOC(1-3) 010 CHOICE="OFF" LINK INIT=JUMPER(3) LOC(1-3) 001