BOARD	;12/21 gha New
 ID="ISAB702"
 NAME="Iomega Bernoulli II Combo Adapter Board"
 MFR="Iomega Corporation"
 CATEGORY="OTH"
 SLOT=ISA8 
 LENGTH=140
 COMMENTS="\n
 NOTE:\n
Set Switch(SW2) to the SCSI bus address and parity checking.  Factory settings
should be adequate (See Board Manual).  Jumpers, JB1 to JB3 are reserved.\n"

SWITCH(1)=8
 NAME="(SW1)I/O PORT,DMA"
 STYPE=DIP
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-8) "1" "2" "3" "4" "5" "6" "7" "8"
 FACTORY=LOC(1-8) 11000000
 INITVAL=LOC(5-8) 0000

JUMPER(1)=4
 NAME="(J6)ROM ADDR."
 JTYPE=TRIPOLE
 VERTICAL=NO
 REVERSE=YES
 LABEL=LOC(1-4) "1" "2" "3" "4"
 FACTORY=LOC(1-4) 1100

SOFTWARE(1)=
 "Match your device drivers with these selected options:"

FUNCTION="Bernoulli II Combo Adapter Board"
 TYPE="OTH"

 SUBFUNCTION="I/O Port Address"
 CHOICE="340H-345H"
  LINK
   PORT = 340h-345h
   INIT = SWITCH(1) LOC(1-2) 11
   INIT = SOFTWARE(1) "I/O Adr 340-345h"
 CHOICE="350H-355H"
  LINK
   PORT = 350H-355H
   INIT = SWITCH(1) LOC(1-2) 01
   INIT = SOFTWARE(1) "I/O Adr 350-355h"
 CHOICE="360H-365H"
  LINK
   PORT = 360H-365H
   INIT = SWITCH(1) LOC(1-2) 10
   INIT = SOFTWARE(1) "I/O Adr 360-365h"
 CHOICE="370H-375H"
  LINK
   PORT = 370H-375H
   INIT = SWITCH(1) LOC(1-2) 00
   INIT = SOFTWARE(1) "I/O Adr 370-375h"
 SUBFUNCTION="Direct Memory Access"
 CHOICE = "DMA Enabled"
  LINK
   DMA = 3 | 1
   INIT = SWITCH(1) LOC(3-4) 00 | 10
   INIT = SOFTWARE(1) "DMA CHL 3" | "DMA CHL 1"
 CHOICE = "DMA Disabled"
  FREE
   INIT = SWITCH(1) LOC(3-4) 01
   INIT = SOFTWARE(1) "NO DMA"
 SUBFUNCTION="ROM Address"
 CHOICE = "ROM Enabled"
  COMBINE
   MEMORY=8K
   ADDRESS=
    0CE000h | 0C8000h | 0CA000h | 0CC000h |
    0D0000h | 0D2000h | 0D4000h | 0D6000h |
    0D8000h | 0DA000h | 0DC000h | 0DE000h |
    0E0000h | 0E2000h | 0E4000h
   MEMTYPE=OTHER
   INIT=JUMPER(1) LOC(1-4)
    1100 | 1111 | 1110 | 1101 |
    1011 | 1010 | 1001 | 1000 |
    0111 | 0110 | 0101 | 0100 |
    0011 | 0010 | 0001
   INIT=SOFTWARE(1)
    "MEM Adr CE000" | "MEM Adr C8000" | "MEM Adr CA000" | "MEM Adr CC000" |
    "MEM Adr D0000" | "MEM Adr D2000" | "MEM Adr D4000" | "MEM Adr D6000" |
    "MEM Adr D8000" | "MEM Adr DA000" | "MEM Adr DC000" | "MEM Adr DE000" |
    "MEM Adr E0000" | "MEM Adr E2000" | "MEM Adr E4000"
 CHOICE = "ROM Disabled"
  FREE
   INIT=JUMPER(1) LOC(1-4)
    0000
   INIT=SOFTWARE(1)
    "NO BRD Memory"