BOARD				     			       
	ID = "NICC005"
	NAME = "National Instruments AT-GPIB Interface Board"
	MFR = "NATIONAL INSTR CORP"
	CATEGORY = "COM"
	SLOT = ISA16
	READID = NO
        LENGTH = 165                               ;16.5cm = 6.5inches
        AMPERAGE = 1500 		   	   ;1.5 Amps
        SKIRT = NO
	COMMENTS = "AT-GPIB EISA configuration file Version 3.0; 
                    For further information call
                    National Instruments at 1-800-433-3488."
	HELP = "Sorry, no help available."

SWITCH(1) = 5
	NAME = "Base I/O Address"
	STYPE = DIP
	VERTICAL = YES
	REVERSE = YES
	LABEL = LOC(1-5) "9" "8" "7" "6" "5" 
	FACTORY = LOC(1-5) 01001
	COMMENTS = "The base I/O address is determined by the settings of the DIP
                    switch (U25).  Note that this switch uses negative
                    logic. If your screen or report shows you a binary
                    representation of the switch, the ones and zeroes will
                    be reversed.  The 'ON' and 'OFF' settings given by the
                    configuration utility are correct."


JUMPER(1) = 11
	NAME = "DMA/High IRQ  (W2)"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-11) "DRQ7" "DACK7" "DRQ6" "DACK6" "DRQ5" "DACK5" "IRQ15" "IRQ14" "IRQ12" "IRQ11" "IRQ10"
	FACTORY = LOC(1-11) 00001100010
        ;Factory defaults - DACK5,DRQ5, and IRQ11                                                             
	COMMENTS = "The DMA channel used is determined by this jumper.
		    Note that both DRQ (request) and DACK (acknowledge) jumpers must
		    be set to the same channel if that channel is to be used. In addition,
		    the high IRQ levels (10, 11, 12, 14, and 15) are selected by this jumper."

		    
JUMPER(2) = 6
	NAME = "Low IRQ Level (W3)"
	JTYPE = PAIRED
	VERTICAL = NO
	REVERSE = YES
	LABEL = LOC(1-6) "IRQ3" "IRQ4" "IRQ5" "IRQ6" "IRQ7" "IRQ9"
	FACTORY = LOC(1-6) 000000
        ;Factory default is IRQ11 
	COMMENTS = "The low IRQ levels (3, 4, 5, 6, 7, and 9) are
		    selected by this jumper.  Only one of the high
		    IRQ or low IRQ levels should be selected."


FUNCTION = "AT-GPIB Interface"
  SUBFUNCTION = "Base I/O Address"
    CHOICE = "2C0"
      LINK
        PORT = 2C0h-2DFh
        INIT = SWITCH(1) LOC(1-5) 01001
    CHOICE = "2E0"
      LINK
        PORT = 2E0h-2FFh
        INIT = SWITCH(1) LOC(1-5) 01000
    CHOICE = "100"
      LINK
        PORT = 100h-11Fh
        INIT = SWITCH(1) LOC(1-5) 10111
    CHOICE = "120"
      LINK
        PORT = 120h-13Fh
        INIT = SWITCH(1) LOC(1-5) 10110
    CHOICE = "140"
      LINK
        PORT = 140h-15Fh
        INIT = SWITCH(1) LOC(1-5) 10101
    CHOICE = "160"
      LINK
        PORT = 160h-17Fh
        INIT = SWITCH(1) LOC(1-5) 10100
    CHOICE = "180"
      LINK
        PORT = 180h-19Fh
        INIT = SWITCH(1) LOC(1-5) 10011
    CHOICE = "1A0"
      LINK
        PORT = 1A0h-1BFh
        INIT = SWITCH(1) LOC(1-5) 10010
    CHOICE = "1C0"
      LINK
        PORT = 1C0h-1DFh
        INIT = SWITCH(1) LOC(1-5) 10001
    CHOICE = "1E0"
      LINK
        PORT = 1E0h-1FFh
        INIT = SWITCH(1) LOC(1-5) 10000
    CHOICE = "200"
      LINK
        PORT = 200h-21Fh
        INIT = SWITCH(1) LOC(1-5) 01111
    CHOICE = "220"
      LINK
        PORT = 220h-23Fh
        INIT = SWITCH(1) LOC(1-5) 01110
    CHOICE = "240"
      LINK
        PORT = 240h-25Fh
        INIT = SWITCH(1) LOC(1-5) 01101
    CHOICE = "260"
      LINK
        PORT = 260h-27Fh
        INIT = SWITCH(1) LOC(1-5) 01100
    CHOICE = "280"
      LINK
        PORT = 280h-29Fh
        INIT = SWITCH(1) LOC(1-5) 01011
    CHOICE = "2A0"
      LINK
        PORT = 2A0h-2BFh
        INIT = SWITCH(1) LOC(1-5) 01010
    CHOICE = "300"
      LINK
        PORT = 300h-31Fh
        INIT = SWITCH(1) LOC(1-5) 00111
    CHOICE = "320"
      LINK
        PORT = 320h-33Fh
        INIT = SWITCH(1) LOC(1-5) 00110
    CHOICE = "340"
      LINK
        PORT = 340h-35Fh
        INIT = SWITCH(1) LOC(1-5) 00101
    CHOICE = "360"
      LINK
        PORT = 360h-37Fh
        INIT = SWITCH(1) LOC(1-5) 00100
    CHOICE = "380"
      LINK
        PORT = 380h-39Fh
        INIT = SWITCH(1) LOC(1-5) 00011
    CHOICE = "3A0"
      LINK
        PORT = 3A0h-3BFh
        INIT = SWITCH(1) LOC(1-5) 00010
    CHOICE = "3C0"
      LINK
        PORT = 3C0h-3DFh
        INIT = SWITCH(1) LOC(1-5) 00001
    CHOICE = "3E0"
      LINK
        PORT = 3E0h-3FFh
        INIT = SWITCH(1) LOC(1-5) 00000


SUBFUNCTION = "DMA Channel"
  CHOICE = "5"
    LINK
      DMA = 5
      SHARE = NO
      TIMING = TYPEB
      INIT = JUMPER(1) LOC(1-6) 000011
  CHOICE = "6"
    LINK
      DMA = 6
      SHARE = NO
      TIMING = TYPEB
      INIT = JUMPER(1) LOC(1-6) 001100
  CHOICE = "7"
    LINK
      DMA = 7
      SHARE = NO
      TIMING = TYPEB
      INIT = JUMPER(1) LOC(1-6) 110000
  CHOICE = "Disabled"
    LINK
      INIT = JUMPER(1) LOC(1-6) 000000


SUBFUNCTION = "Interrupt Request Level"
  CHOICE = "11"
    LINK
      IRQ = 11
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(1) LOC(7-11) 00010
      INIT = JUMPER(2) LOC(1-6)  000000
  CHOICE = "10"
    LINK
      IRQ = 10
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(1) LOC(7-11) 00001
      INIT = JUMPER(2) LOC(1-6)  000000
  CHOICE = "5"	     
    LINK
      IRQ = 5
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(2) LOC(1-6)  001000
      INIT = JUMPER(1) LOC(7-11) 00000
  CHOICE = "7"
    LINK
      IRQ = 7
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(2) LOC(1-6)  000010
      INIT = JUMPER(1) LOC(7-11) 00000
  CHOICE = "9"	     
    LINK
      IRQ = 9
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(2) LOC(1-6)  000001
      INIT = JUMPER(1) LOC(7-11) 00000
  CHOICE = "12"
    LINK
      IRQ = 12
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(1) LOC(7-11) 00100
      INIT = JUMPER(2) LOC(1-6)  000000
  CHOICE = "3"
    LINK
      IRQ = 3
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(2) LOC(1-6 ) 100000
      INIT = JUMPER(1) LOC(7-11) 00000
  CHOICE = "4"
    LINK
      IRQ = 4
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(2) LOC(1-6)  010000
      INIT = JUMPER(1) LOC(7-11) 00000
  CHOICE = "14"
    LINK
      IRQ = 14
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(1) LOC(7-11) 01000
      INIT = JUMPER(2) LOC(1-6)  000000
  CHOICE = "15"
    LINK
      IRQ = 15
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(1) LOC(7-11) 10000
      INIT = JUMPER(2) LOC(1-6)  000000
  CHOICE = "6"
    LINK
      IRQ = 6
      SHARE = NO
      TRIGGER = EDGE
      INIT = JUMPER(1) LOC(7-11) 00000
      INIT = JUMPER(2) LOC(1-6)  000100
  CHOICE = "Disabled"
    LINK
      INIT = JUMPER(1) LOC(7-11) 00000
      INIT = JUMPER(2) LOC(1-6)  000000