Article: Q68128
Product(s): Microsoft Windows 3.x Retail Product
Version(s): WINDOWS:3.0,3.0a,3.1,3.11
Operating System(s):
Keyword(s): win31
Last Modified: 18-SEP-1999
3.00 3.00a 3.10 3.11
WINDOWS
kbfasttip kbtshoot
-------------------------------------------------------------------------------
The information in this article applies to:
- Microsoft Windows versions 3.0, 3.0a, 3.1, 3.11
-------------------------------------------------------------------------------
SYMPTOMS
========
When you run or install Microsoft Windows, you may encounter the following
problems: corrupted or incomplete installation of Windows, insufficient memory
or file handles, and/or an inability to use standard and enhanced modes of
Windows.
CAUSE
=====
Your CONFIG.SYS and AUTOEXEC.BAT files contain device drivers,
terminate-and-stay-resident (TSR) programs, and other files.
WORKAROUND
==========
To reduce or eliminate these problems, follow the instructions in the More
Information section of this article to modify the CONFIG.SYS and AUTOEXEC.BAT
files.
Use a text editor such as MS-DOS EDIT, EDLIN programs, or Windows Notepad to edit
your CONFIG.SYS and AUTOEXEC.BAT files.
NOTE: Make backup copies of the the AUTOEXEC.BAT and CONFIG.SYS files, before you
make your changes.
MORE INFORMATION
================
CONFIG.SYS File
---------------
Modify the CONFIG.SYS file as follows:
1. Remove nonessential device drivers such as keyboard buffers, scanner drivers,
printer drivers, and country drivers. If you are unsure of what a device
driver does, do NOT remove it.
2. Remove FASTOPEN statements and disk caches.
3. Verify that you have at least 60 FILES, and 20 BUFFERS.
4. If you are using MS-DOS version 3.3 or later, add a STACKS=0,0 line to your
CONFIG.SYS file. For MS-DOS version 3.2, the line should read STACKS=9,192.
For more information on STACKS, query on the following words in the Microsoft
Knowledge Base:
stacks and explanation and config
5. If you have a SHELL=COMMAND.COM /P /E:256 statement, increase the number
following the E: (the environment space) to 2048. Verify that the /p switch
is used. If you do not have a SHELL command, you may want to add one, making
sure that the path to COMMAND.COM in the SHELL statement matches the COMSPEC
statement. At the command prompt, type
set
This command will give you the path to which the location COMSPEC is pointing.
AUTOEXEC.BAT File
-----------------
Modify the AUTOEXEC.BAT file as follows:
1. Remove any nonessential programs such as TSR programs, print buffers and
APPEND, JOIN, SUBST, PRINT, and GRAPHICS statements. If you are unsure of
what a program does, do NOT remove it.
2. Remove all duplicate PATH entries so you only have one PATH line in your
AUTOEXEC.BAT file. Modify your PATH statement so it uses the root, MS-DOS,
and Windows directories only.
3. Verify that you have a valid SET TEMP statement to an existing directory. For
example, SET TEMP=C:\WINDOWS\TEMP.
Additional Troubleshooting Steps
--------------------------------
- Verify that the File Allocation Table is valid:
1. Exit Windows.
2. At the command prompt, type the following:
chkdsk /f
Caution: You must Exit Windows BEFORE you type the above command. CHKDSK will
also check the directory structure.
- Verify that you are using the proper version of DOS for your computer. For
example, if you are using a COMPAQ computer, you should be using a version of
COMPAQ DOS.
- Verify that the path, environment space, and TEMP directory are valid. At the
command prompt, type:
set
Reinstall Windows after you make the above changes to the CONFIG.SYS and
AUTOEXEC.BAT files.
NOTE: Before you reinstall Windows, switch your computer off, wait a few seconds,
and switch your computer on again and read the new CONFIG.SYS and AUTOEXEC.BAT
files to verify your changes.
- To determine the function of certain drivers when Windows will not run,
create a MS-DOS boot floppy disk containing the following CONFIG.SYS file and
AUTOEXEC.BAT files and boot from the floppy disk.
CONFIG.SYS: AUTOEXEC.BAT:
FILES=50 PATH=C:\WINDOWS;C:\DOS
BUFFERS=20 PROMPT $P$G
DEVICE=C:\HIMEM.SYS SET TEMP=C:\WINDOWS\TEMP
If, after booting, you can access the hard disk properly (CHKDSK gives the
same output as before) try to run Windows.
If CHKDSK gives different output, do NOT run CHKDSK /F in this state. You may
have booted without a driver necessary to access the hard drive properly.
Remove the floppy and reboot from the hard drive.
For more information on troubleshooting similar Windows problems, query on the
following word in the Microsoft Knowledge Base:
tshoot
REFERENCES
==========
"Getting Started with Microsoft Windows," version 3.1, page 100
"Microsoft Windows User's Guide," version 3.0, page 515
Additional query words: 3.00 3.00a 3.10 3.11 clean boot
======================================================================
Keywords : win31
Technology : kbWin3xSearch kbZNotKeyword3 kbWin300 kbWin300a kbWin310 kbWin311
Version : WINDOWS:3.0,3.0a,3.1,3.11
=============================================================================