17.619 bytes

Service Hints & Tips

Document ID: PMYS-3R6J5E

Aptiva - List of common configuration Error Codes

Applicable to: World-Wide

The list of configuration error codes below contains some of the more common bootup error codes that may be encountered in the Aptiva systems.

These error codes are not related to the operating system on the computer, but are instead an indication of a hardware configuration problem. The codes are included here for the convenience of computer users, since the codes will seem to appear when the operating system is booted.

These configuration error codes may also be referred to as POST codes. When the system is powered on, the system BIOS executes a series of tests, called the Power On Self Test (POST), to check the hardware configuration and components in the system. In the Aptiva systems, these POST codes are more often seen as Configuration Error codes when displayed during bootup.

Post Error Codes

Note: X Represents any number not otherwise listed.

Code: Description:

01X Undetermined problem errors

02X Power supply errors

1XX System board errors
101 System board error - interrupt failure
102 System board error - timer failure
103 System board error - timer interrupt failure
104 System board error - protected mode failure
105 System board error - last 8042 command not accepted
106 System board error - converting logic test
107 System board error - hot NMI test
108 System board error - timer bus test
109 Direct memory access (DMA) test error
110 System board memory error - parity
111 System board error - adapter card
112 System board error - adapter card
113 System board error - adapter card
121 Unexpected hardware interrupts occurred
129 Cache error - unsupported CPU upgrade
131 Cassette wrap test failed
161 System options error (run setup) - battery failure
162 System options not set correctly - run setup
163 Date and time not set - run setup (F1)
164 Memory size error - run setup
166 System board error - adapter card
181 System board error - adapter card
199 User-indicated configuration not correct

2XX Memory (RAM) errors
201 Memory test failed
202 Memory address error
203 Memory address error

3XX Keyboard / Cable error
301 Keyboard did not respond to software reset correctly, or a stuck key failure was detected. If a stuck key was detected, the scan code for the key is displayed in hexadecimal. For example, the error code 49-301 indicates that key 73, the PgUp key, has failed (49 Hex = 73 Decimal)

302 User-indicated error for the keyboard test, or AT keylock is locked
303 Keyboard or system unit error
304 Keyboard or system unit error; CMOS does not match system

4XX Monochrome monitor errors
401 Monochrome memory test, horizontal sync. frequency test, or video test failed
408 User-indicated display attributes failure
416 User-indicated character set failure
424 User-indicated 80 x 25 mode failure
425 Parallel port test failed (monochrome adapter)

5XX Display (color monitors) errors - video port or monitor
501 Color memory test failed, horizontal sync frequency test or video test failed
508 User-indicated display attribute failure
516 User-indicated character set failure
524 User-indicated 80 x 25 mode failure
532 User-indicated 40 x 25 mode failure
540 User-indicated 320 x 200 graphics mode failure
548 User-indicated 640 x 200 graphics mode failure

6XX Diskette drive or controller errors
601 Diskette power-on diagnostics test failed
602 Diskette test failed - boot record not valid
606 Diskette verify function failed
607 Write-protected diskette
608 Bad command - diskette status returned
610 Diskette initialization failed
611 Timeout - diskette status returned
612 Bad NEC - diskette status returned (controller)
613 Bad DMA - diskette status returned
621 Bad seek - diskette status returned
622 Bad CRC - diskette status returned
623 Record not found - diskette status returned
624 Bad address mark - diskette status returned
625 Bad NEC seek - diskette status returned
626 Diskette data compare error

7XX Math coprocessor

8XX Parallel printer adapter errors
801 Parallel printer adapter test failed

9XX System Board parallel Printer Port

10XX Asynchronous communications adapter errors
1101 Asynchronous communications adapter test failed

11XX Serial port or device error

12XX Alternate asynchronous communications adapter errors
1201 Alternate asynchronous communications adapter test failed

13XX Game control adapter errors
1301 Game control adapter test failed
1302 Joystick test failed

14XX Printer errors
1401 Printer test failed
1402 Matrix printer failed

15XX Synchronous data link control (SDLC) communications adapter errors
1510 8255 port B failure
1511 8255 port A failure
1512 8255 port C failure
1513 8253 timer 1 did not reach terminal count
1514 8253 timer 1 stuck on
1515 8253 timer 0 did not reach terminal count
1516 8253 timer 0 stuck on
1517 8253 timer 2 did not reach terminal count
1518 8253 timer 2 stuck on
1519 8273 port B error
1520 8273 port A error
1521 8273 command/read timeout
1522 Interrupt level 4 failure
1523 Ring indicate stuck on
1524 Receive clock stuck on
1525 Transmit clock stuck on
1526 Test indicate stuck on
1527 Ring indicate not on
1528 Receive clock not on
1529 Transmit clock not on
1530 Test indicate not on
1531 Data set ready not on
1532 Carrier detect not on
1533 Clear to send no on
1534 Data set ready not on
1536 Clear to send stuck on
1537 Level 3 interrupt failure
1538 Receive interrupt results error
1539 Wrap data miscompare
1540 DMA channel 1 error
1541 DMA channel 1 error
1542 Error in 8273 error checking or status reporting
1547 Stray interrupt level 4
1548 Stray interrupt level 3
1549 Interrupt presentation sequence timeout

16XX Display emulation errors (327X, 5520, 525X)

17XX Fixed disk drive/cable (non-SCSI)
1701 Fixed disk POST error
1702 Fixed disk adapter error
1703 Fixed disk drive error
1704 Fixed adapter or drive error
1780 Fixed disk 0 failure
1781 Fixed disk 1 failure
1790 Fixed disk controller failure
1790 Fixed disk 0 failure
1791 Fixed disk 1 failure

18XX I/O expansion unit errors
1801 I/O expansion unit POST error
1810 Enable/disable failure
1811 Extender card wrap test failed (disabled)
1812 High order address lines failure (disabled)
1813 Wait state failure (disabled)
1814 Enable/disable could not be set on
1815 Wait state failure (disabled)
1816 Extender card wrap test failed (enabled)
1817 High order address lines failure (enabled)
1818 Disable not functioning
1819 Wait request switch not set correctly
1820 Receiver card wrap test failure
1821 Receiver high order address lines failure

19XX 3270 PC attachment card errors

20XX Binary synchronous communications (BSC) adapter errors
2010 8255 port A failure
2011 8255 port B failure
2012 8255 port C failure
2013 8253 timer 1 did not reach terminal count
2014 8253 timer 1 stuck on
2016 8253 timer 2 did not reach terminal count or timer 2 stuck on
2017 8251 data set ready failed to come on
2018 8251 clear to send not sensed
2019 8251 data set ready stuck on
2020 8251 clear to send stuck on
2021 8251 hardware reset failed
2022 8251 software reset failed
2023 8151 software "error reset" failed
2024 8251 transmit ready did not come on
2025 8251 receive ready did not come on
2026 8251 could not force "overrun" error status
2027 Interrupt failure - no timer interrupt
2028 Interrupt failure - transmit, replace card or planar
2029 Interrupt failure - transmit, replace card
2030 Interrupt failure - receive, replace card or planar
2031 Interrupt failure - receive, replace card
2033 Ring indicate stuck on
2034 Receive clock stuck on
2035 Transmit clock stuck on
2036 Test indicate stuck on
2037 Ring indicate stuck on
2038 Receive clock not on
2039 Transmit clock not on
2040 Test indicate not on
2041 Data set ready not on
2042 Carrier detect not on
2043 Clear to send not on
2044 Data set ready stuck on
2045 Carrier detect stuck on
2046 Clear to send stuck on
2047 Unexpected transmit interrupt
2048 Unexpected receive interrupt
2049 Transmit data did not equal receive data
2050 8251 detected overrun error
2051 Lost data set ready during data wrap
2052 Receive timeout during data wrap

21XX Alternate binary synchronous communications adapter errors
2110 8255 port A failure
2111 8255 port B failure
2112 8255 port C failure
2113 8263 timer 1 did not reach terminal count
2114 8253 timer 1 stuck on
2115 8253 timer 2 did not reach terminal count or timer 2 stuck on
2116 8251 data set ready failed to come on
2117 8251 clear to send not sensed
2118 8251 data set ready stuck on
2119 8251 clear to send stuck on
2120 8251 hardware reset failed
2121 8251 software reset failed
2122 8251 software "error reset" failed
2123 8251 transmit ready did not come on
2124 8251 receive ready did not come on
2125 8251 could not force "overrun" error status
2126 Interrupt failure - no timer interrupt
2128 Interrupt failure - transmit, replace card or planar
2129 Interrupt failure - transmit, replace card
2130 Interrupt failure - receive, replace card or planar
2131 Interrupt failure - receive, replace card
2133 Ring indicate stuck on
2134 Receive clock stuck on
2135 Transmit clock stuck on
2136 Test indicate stuck on
2137 Ring indicate stuck on
2138 Receive clock not on
2139 Transmit clock not on
2140 Test indicate not on
2141 Data set ready not on
2142 Carrier detect not on
2143 Clear to send not on
2144 Data set ready stuck on
2145 Carrier detect stuck on
2146 Clear to send stuck on
2147 Unexpected transmit interrupt
2148 Unexpected receive interrupt
2149 Transmit data did not equal receive data
2150 8251 detected overrun error
2151 Lost data set ready during data wrap
2152 Receive timeout during data wrap

22XX Cluster adapter errors

24XX Enhanced graphics adapter errors

26XX XT/370 error codes

27XX XT/370 error codes

29XX Color matrix printer errors

30XX Primary PC network adapter errors
3001 CPU failure
3002 ROM failure
3003 ID failure
3004 RAM failure
3005 HIC failure
3006 +/- 12v failed
3007 Digital loopback failure
3008 Host detected HIC failure
3009 Sync fail & no go bit
3010 HIC test ok & no go bit
3011 Go bit & no CMD 41
3012 Card not present
3013 Digital failure (fall thru)
3015 Analog failure
3041 Hot carrier (not this card)
3042 Hot carrier (THIS CARD!)

31XX Secondary PC network adapter errors
3101 CPU failure
3102 ROM failure
3103 ID failure
3104 RAM failure
3105 HIC failure
3106 +/- 12v failed
3107 Digital loopback failure
3108 Host detected HIC failure
3109 Sync fail & no go bit
3110 HIC test ok & no go bit
3111 Go bit & no CMD 41
3112 Card not present
3113 Digital failure (fall thru)
3115 Analog failure
3141 Hot carrier (not this card)
3142 Hot carrier (THIS CARD!)

33XX Compact printer errors

(The section below applies to systems with media consoles)

5803 Keyboard error
5806 Diskette drive error
5859 CD - ROM or Access Station Host or Client card, or cable.
5862 CD - ROM or Access Station Host or Client card, or cable.
8601 Pointing device error.

The descriptions for each of the error codes can help to localize some of the more common problems. A recent hardware change will cause these errors, such as adding memory, a second hard drive, or adapter card. Pressing "F1" to go to the hardware configuration screen and then pressing "Esc" accepting the changes and saving them will often cause these errors to disappear at the next power on bootup.

If the error code persists, the error may be the result of incorrect insertion of chips or adapter cards in their sockets, bad chips or adapter cards, or a conflict of hardware options for adapter cards.

If the hardware changes have been reseated, reinstalled, and double-checked, and the problem still occurs, try removing the change to see if the error still occurs. If it does not occur, then the problem is with the hardware change.

Search Keywords

Hint Category

BIOS, Error Messages, Diagnostics

Date Created

28-01-98

Last Updated

14-12-98

Revision Date

14-12-99

Brand

IBM Aptiva

Product Family

Aptiva

Machine Type

2134, 2136, 2137, 2140, 2142, 2144, 2159, 2161, 2162, 2168, 2176

Model

All

TypeModel

Retain Tip (if applicable)

Reverse Doclinks
and Admin Purposes