|
34.848 bytes |
Service Hints & Tips |
Document ID: DSET-3CNKSA |
Aptiva - Mwave diagnostic error codes
Applicable to: World-Wide
In Numerical Order---
Error Code Modifier Descriptor
000001x0-----------------Mwave adapter not detected by reading
Chip-ID or Chip-ID is invalid
000002xn---------------- Error with AZ-COM Riser card
n=1 -5V over current condition
n=2 -12V over current condition
n=3 -5V and -12V over current condition
n=4 +5V over current condition
n=5 +5V and -5V over current condition
n=6 +5V and -12V over current condition
n=7 +5V, -5V and -12V over current condition
n=8 +12V over current condition
n=9 +12V and -5V over current condition
n=A +12V and -12V over current condition
n=B +12V,-5V and -12V over current condition
n=C +12V and +5V over current condition
n=D +12V, +5V and -5V over current condition
n=E +12V, +5V and -12V over current condition
n=F +12V, +5V, -12V and -5V over current condition
n=G No card detected or plugged into AZ-COM Riser
000003xn-----------------Data bus access error
n=1 Low byte = 'AA' failed
n=2 High byte = '05' failed
000004xn-----------------Data bus access error
n=1 Low byte = '55' failed
n=2 High byte = '7A' failed
000005xn-----------------Data bus access error
n=0 Bit 15 only failed
000006xn-----------------Data bus access error
n=0 BHE/BLE bit failed
000007xn-----------------DSP Data store error (1st location check)
n=1 Low byte bad
n=2 High byte bad
n=3 Both bytes bad
000009xn-----------------DSP Data store error (Data line check)
n=1 Low byte bad
n=2 High byte bad
n=3 Both bytes bad
000010xn-----------------DSP Data store error
n=0 Address line check failed
000012xn-----------------DSP Instruction store error (1st location check)
n=1 Low byte bad
n=2 Middle byte bad
n=3 Low and middle bytes bad
n=4 High byte bad
n=5 High and low bytes bad
n=6 High and middle bytes bad
n=7 All bytes bad
000014xn-----------------DSP Instruction store error (Data line check)
n=1 Low byte bad
n=2 Middle byte bad
n=3 Low and middle bytes bad
n=4 High byte bad
n=5 High and low bytes bad
n=6 High and middle bytes bad
n=7 All bytes bad
000015xn-----------------DSP Instruction store error
n=0 Address line check failed
000017xn-----------------Error downloading DSP code to DSP instruction store
n=1 Written Instruction store checksum doesn't match read checksum
000018xn-----------------DSP initialization (IPL) error
n=A No additional error information
n=B IPL timed out error
n=E DSP couldn't brach to do IPL
n=F Instruction ram checksum Error
n=G Data ram checksum Error
n=H Instruction ram r/w validity
n=I Instruction ram addressing validity
n=J Data ram r/w validity
n=K Data ram addressing validity
n=L Creating IDM pointer table Error
n=M Core test (multiplier/ALU/Branches/etc)
000019xn-----------------Init DSP before doing Data store RAM check
n=1 Written Instruction store checksum doesn't match read checksum
000020xn-----------------Bus arbitration error (DMA from PC to DSP) DMA Channel (0)
n=D Expected data does not match what was transferred
000021xn-----------------Bus arbitration error (DMA from DSP to PC) DMA Channel (0)
n=D Expected data does not match what was transferred
000022xn-----------------Bus arbitration error (DMA from PC to DSP) DMA Channel (1)
n=D Expected data does not match what was transferred
000023xn-----------------Bus arbitration error (DMA from DSP to PC) DMA Channel (1)
n=D Expected data does not match what was transferred
000024xn-----------------Bus arbitration error (DMA from PC to DSP) DMA Channel (6)
n=D Expected data does not match what was transferred
000025xn-----------------Bus arbitration error (DMA from DSP to PC) DMA Channel (6)
n=D Expected data does not match what was transferred
000026xn-----------------Bus arbitration error (DMA from PC to DSP) DMA Channel (7)
n=D Expected data does not match what was transferred
000027xn-----------------Bus arbitration error (DMA from DSP to PC) DMA Channel (7)
n=D Expected data does not match what was transferred
000032xn-----------------MIDI error - External loopback
n=1 Problem with simple I/O
n=2 Problem emptying Tx
n=3 Rx data not found
n=4 Forced framing error not found
n=5 Forced overrun error not found
n=6 Overrun or Framing error found when we shoudn't
n=7 Tx not empty when it should be
n=8 Interrupt error - did not occur
n=9 Couldn't force a Tx over fill error
n=B Couldn't put MSP into MPU-401 mode
000035xn-----------------JOYSTICK error - Wipers
n=1 Joystick A X wiper bad 50k ohm position
n=2 Joystick A Y wiper bad 100k ohm position
n=3 Joystick B X wiper bad 50k ohm position
n=4 Joystick B Y wiper bad 100k ohm position
n=5 Joystick B Y wiper bad 50k ohm position
n=6 Joystick B X wiper bad 100k ohm position
n=7 Joystick A Y wiper bad 50k ohm position
n=8 Joystick A X wiper bad 100k ohm position
n=E Joystick timeout error - relay position = 0
n=F Joystick timeout error - relay position = 1
000036xn-----------------JOYSTICK error - Triggers
n=1 Joystick A Button 1 didn't go low
n=2 Joystick A Button 2 didn't go high
n=3 Joystick B Button 1 didn't go low
n=4 Joystick B Button 2 didn't go high
n=5 Joystick A Button 1 didn't go high
n=6 Joystick A Button 2 didn't go low
n=7 Joystick B Button 1 didn't go high
n=8 Joystick B Button 2 didn't go low
000042xn-----------------DSP Interrupt error (IRQ 5)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000043xn-----------------DSP Interrupt error (IRQ 3)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000044xn-----------------DSP Interrupt error (IRQ 4)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000045xn-----------------DSP Interrupt error (IRQ 7)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000046xn-----------------DSP Interrupt error (IRQ 10)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000047xn-----------------DSP Interrupt error (IRQ 9)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000049xn-----------------DSP Interrupt error (IRQ 11)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000050xn-----------------UART error - Comm 1, IRQ 4
n=2 Bad Line Status Register value
n=3 TX FIFO empty when expected un-empty
n=4 TX Character verify fail
n=5 RX Character verify fail
n=6 Bad Line Status Register value from RX character
n=7 Error installing COM Interrupt service routine
n=8 Unexpected COM Interrupt received
n=9 Expected COM Interrupt not received
n=A Wrong Interrupt in IIR
000051xn-----------------UART error - Comm 2, IRQ 3
n=2 Bad Line Status Register value
n=3 TX FIFO empty when expected un-empty
n=4 TX Character verify fail
n=5 RX Character verify fail
n=6 Bad Line Status Register value from RX character
n=7 Error installing COM Interrupt service routine
n=8 Unexpected COM Interrupt received
n=9 Expected COM Interrupt not received
n=A Wrong Interrupt in IIR
000052xn-----------------UART error - Comm 3, IRQ 10
n=2 Bad Line Status Register value
n=3 TX FIFO empty when expected un-empty
n=4 TX Character verify fail
n=5 RX Character verify fail
n=6 Bad Line Status Register value from RX character
n=7 Error installing COM Interrupt service routine
n=8 Unexpected COM Interrupt received
n=9 Expected COM Interrupt not received
n=A Wrong Interrupt in IIR
000053xn-----------------UART error - Comm 4, IRQ 11
n=2 Bad Line Status Register value
n=3 TX FIFO empty when expected un-empty
n=4 TX Character verify fail
n=5 RX Character verify fail
n=6 Bad Line Status Register value from RX character
n=7 Error installing COM Interrupt service routine
n=8 Unexpected COM Interrupt received
n=9 Expected COM Interrupt not received
n=A Wrong Interrupt in IIR
000065xn-----------------Telephone (1 line) RING DETECT error
n=1 Ring time HIGH value failed too high
n=2 Ring time HIGH value failed too low
n=3 Ring time LOW value failed too high
n=4 Ring time LOW value failed too low
n=7 DSP task failed for unknown reason
000069xn-----------------4231 basic communications error
n=1 bit 1 from reading Index reg 0xE failed
n=2 bit 2 from reading Index reg 0xE failed
n=3 bit 3 from reading Index reg 0xE failed
n=4 bit 4 from reading Index reg 0xE failed
n=5 bit 5 from reading Index reg 0xE failed
n=6 bit 6 from reading Index reg 0xE failed
n=7 bit 7 from reading Index reg 0xE failed
n=8 bit 8 from reading Index reg 0xE failed
000070xn-----------------Audio loopback error - (Left/Right DAC out to AUX 1 input)
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000071xn-----------------Audio loopback error - (Left/Right DAC out to MIC-in )
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000073xn-----------------Audio loopback error - Earspeaker out to MIC-in at +26dB Switches = A7,A3,B3,B5,B1,A1)
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000080xn-----------------Audio loopback error - CD-ROM audio connector From CD player - requires IBM test CD
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000081xn-----------------Audio loopback error - CD-ROM audio connector From MFG BOX sine wave
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000082xn-----------------Audio loopback error - INTA audio connector From MFG BOX sine wave to AUX 1 input
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000083xn---------------- Audio loopback error - INTB audio connector From MFG BOX sine wave to Line-in input
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000088xn-----------------Internal OPL3 Audio test
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000096xn-----------------Telephone (1 line) Caller-ID loopback error Audio Codec out thru Handset thru Line 1 to AIC1 Left "ON-HOOK" - Caller-ID bit set
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
000098xn-----------------Telephone (1 line) loopback error AIC1 out thru Line 1 to Handset to Audio Codec
n=1 Right channel RMS value measured low
n=2 Right channel RMS value measured high
n=3 Left channel RMS value measured low
n=4 Both channels RMS value measured low
n=5 Left channel RMS value measured low, Right channel measured high
n=6 Left channel RMS value measured high
n=7 Left channel RMS value measured high, Right channel measured low
n=8 Both channels RMS value measured high
n=A 2nd data = 9063 - didn't go ONHOOK
n=B 2nd data = 9463 - didn't go OFFHOOK
n=C 2nd data = 1463 - didn't go ONHOOK
n=D 2nd data = 9463 - didn't go OFFHOOK
000099xn-----------------Telephone (1 line) loopback error Audio Codec out thru Handset thru Line 1 to AIC1
n=3 RMS value measured low
n=6 RMS value measured high
n=A 2nd data = 9063 - didn't go ONHOOK
n=B 2nd data = 9463 - didn't go OFFHOOK
n=C 2nd data = 1463 - didn't go ONHOOK
n=D 2nd data = 9463 - didn't go OFFHOOK
000121xn-----------------4236 Interrupt error (IRQ 5)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000122xn-----------------4236 Interrupt error (IRQ 7)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000123xn-----------------4236 Interrupt error (IRQ 9)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000124xn-----------------4236 Interrupt error (IRQ 10)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000125xn-----------------4236 Interrupt error (IRQ 11)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000126xn-----------------4236 Interrupt error (IRQ 15)
n=1 Interrupt occured but data in DSP reg bad
n=2 Multiple interrupts occured
n=5 No interrupt occured
000130xn-----------------MIDI error - Internal loopback (0x300, IRQ=5)
n=1 Problem with simple I/O
n=2 Problem emptying Tx
n=3 Rx data not found
n=4 Forced framing error not found
n=5 Forced overrun error not found
n=6 Overrun or Framing error found when we shoudn't
n=7 Tx not empty when it should be
n=8 Interrupt error - did not occur
n=9 Couldn't force a Tx over fill error
n=B Couldn't put MSP into MPU-401 mode
000132xn-----------------MIDI error - Internal loopback (0x300, IRQ=7)
n=1 Problem with simple I/O
n=2 Problem emptying Tx
n=3 Rx data not found
n=4 Forced framing error not found
n=5 Forced overrun error not found
n=6 Overrun or Framing error found when we shoudn't
n=7 Tx not empty when it should be
n=8 Interrupt error - did not occur
n=9 Couldn't force a Tx over fill error
n=B Couldn't put MSP into MPU-401 mode
000133xn-----------------MIDI error - Internal loopback (0x330, IRQ=9)
n=1 Problem with simple I/O
n=2 Problem emptying Tx
n=3 Rx data not found
n=4 Forced framing error not found
n=5 Forced overrun error not found
n=6 Overrun or Framing error found when we shoudn't
n=7 Tx not empty when it should be
n=8 Interrupt error - did not occur
n=9 Couldn't force a Tx over fill error
n=B Couldn't put MSP into MPU-401 mode
000134xn-----------------MIDI error - Internal loopback (0x330, IRQ=10)
n=1 Problem with simple I/O
n=2 Problem emptying Tx
n=3 Rx data not found
n=4 Forced framing error not found
n=5 Forced overrun error not found
n=6 Overrun or Framing error found when we shoudn't
n=7 Tx not empty when it should be
n=8 Interrupt error - did not occur
n=9 Couldn't force a Tx over fill error
n=B Couldn't put MSP into MPU-401 mode
000135xn-----------------MIDI error - Internal loopback (0x330, IRQ=11)
n=1 Problem with simple I/O
n=2 Problem emptying Tx
n=3 Rx data not found
n=4 Forced framing error not found
n=5 Forced overrun error not found
n=6 Overrun or Framing error found when we shoudn't
n=7 Tx not empty when it should be
n=8 Interrupt error - did not occur
n=9 Couldn't force a Tx over fill error
n=B Couldn't put MSP into MPU-401 mode
|
Search Keywords |
| |
|
Hint Category |
Diagnostics, Mwave, Error Messages | |
|
Date Created |
24-12-96 | |
|
Last Updated |
17-02-99 | |
|
Revision Date |
16-02-2000 | |
|
Brand |
IBM Aptiva | |
|
Product Family |
Aptiva | |
|
Machine Type |
2134, 2144, 2159, 2168, 2176 | |
|
Model |
C23; C31; C32; C33; C35; C3X; C53; C55; C5X; C65; C66; C67; C6B; C6D; C6E; C6V; C6X; C6Y; C73; C77; C7X; 6R8; 6R9; 7R0; 7R1; 7R2; 7R3; 7R6; 7R7; 7R9; 8R1; 8R6; 8R8; 9R2; 9R3; 9R4; 9R5; 9R6; F23; F31; F32; F33; F35; F67; F6B; M40; M41; M53; M54; M55; M56; M57; M58; M60; M61; M62; M70; M71; M72; M91; A40; A44; A45; A50; A51; A52; A90; A92; A94; 2R6; 3R5; 4R2; 4R7; 2R9; 3R3; 3R1; 4R8; 3R0; 3R7; 4R0; 4R9; 3R8; 3R9; 4R3; 5R5; C40; C41; C45; C53; C61; M30; M31; M35; M50; M51; M52; M63; A10; A12; A14; 2R0; 2R3; 2R0; 2R3; 2R5; 2R7; 2R8; 3R4; 3R6; 4R1; 5R1; 6R3; C30; C31; C51; C21; 6R6; 132; 142; 152; 154; 162; 163; 172; 182; L15; L16; K25; K26; L33; K33; L43; K43; L35; K35; L45; K45; KU5; L55; K55; L65; K65; L66; K66; U15; U16; U33; U43; U35; U45; U55; U65; U66; X17; X27; X37; X47; Y17; Y27; Y37; Y47; Z17; Z27; Z37; Z47; S55; S65; S64; S74; S75; W37; W47; S20; 932; 9W2; LL5; LL6; L50; L60; K50; K60; LL1; LL2; LL3; LL4; L10; L20; L30; L40; K10; K20; KU6; K30; K40; KU4; X40; Y40; Z40; N50; N51; N60; N61; N71; Y10; Y20; Y30; Z10; Z20; Z30; X10; X20; X30; W30; N30; N40; N41; 352; 354; 355; 356; 357; 362; 363; 364; 372; 374; 381; 382; 384; 392; 442; 443; 447; 449; 454; 6R8; 6R9; 7R0; 7R1; 7R2; 7R3; 7R6; 7R7; 7R9; 8R1; 8R6; 8R8; 9R1; 9R3; 9R4; 9R5; 9R6; C23; C31; C32; C33; C35; C3X; C53; C55; C5X; C65; C66; C67; C6B; C6D; C6E; C6X; C6Y; C6Z; C73; C77; C7X; F23; F31; F32; F33; F35; F67; F6B; H54; H55; H56; H5E; H5F; H64; H65; H6D; H6E; H6F; H7E; H7F; H7G; J33; J35; J3C; J3E; J3K; J3L; J3V; J3W; J3Y; J3Z; JCL; K53; J62; K74; L53; L62; P53; P62; T01; T33; T34; T62; T63; T65; T71; V34; V65; V71; W33; W55; W65; X01; X31; X33; X34; X52; X62; X63; X65; X71; Y01; Y04; Y31; Y33; Y34; Y52; Y62; Y63; Y65; Y71; Z01; Z31; Z33; Z34; Z52; Z62; Z63; Z65; Z71; 446; 6R6; C21; J31; J3A; J3X; J51; J52; JDA; JSN; K01; K21; K22; K23; K31; K32; K52; L01; L21; L22; L23; L31; L32; L52; L6T; P01; P21; P22; P23; P31; P32; P52; 13R; 14R; 15R; 16R; 19R; 20R; S64; S66; S74; S76; S78; S7H; C6Z; 9R1 | |
|
TypeModel |
| |
|
Retain Tip (if applicable) |
| |
|
Reverse Doclinks |