|
35.413 bytes |
Service Hints & Tips |
Document ID: DETR-3YTQT6 |
|
This document is provided to IBM and our Business Partners to help sell and/or service IBM products. It is not to be distributed beyond that audience or used for any other purpose. |
Aptiva - Remote Access Server (RAS) error codes
Applicable to: World-Wide
Summary:
The table below lists the error codes that Remote Access Service (RAS) reports in Windows 95/98.
|
RAS Code |
Description |
Category |
|
-1 |
No Data |
Unknown |
|
0 |
Connection successful |
Success |
|
3 |
Disconnect successful |
Success |
|
600 |
An operation is pending |
Unknown |
|
601 |
The port handle is invalid |
Unknown |
|
602 |
The port is already open |
User Error |
|
603 |
Caller buffer is too small |
Unknown |
|
604 |
Wrong information specified |
Configuration Error |
|
605 |
Cannot set port information |
Configuration Error |
|
606 |
The port is not connected |
User Error |
|
607 |
The event is invalid |
Unknown |
|
608 |
The device does not exist |
Configuration Error |
|
609 |
The device type does not exist |
Configuration Error |
|
610 |
The buffer is invalid |
Unknown |
|
611 |
The route is not available |
Configuration Error |
|
612 |
The route is not allocated |
Configuration Error |
|
613 |
Invalid compression specified |
Unknown |
|
614 |
Out of buffers |
Unknown |
|
615 |
The port was not found |
Configuration Error |
|
616 |
An asynchronous request is pending |
Unknown |
|
617 |
The port or device is already disconnecting |
User Error |
|
618 |
The port is not open |
Unknown |
|
619 |
The port is disconnected |
User Error |
|
620 |
There are no endpoints |
Configuration Error |
|
621 |
Cannot open the phone book file |
Configuration Error |
|
622 |
Cannot load the phone book file |
Configuration Error |
|
623 |
Cannot find the phone book entry |
Configuration Error |
|
624 |
Cannot write the phone book file |
Configuration Error |
|
625 |
Invalid information found in the phone book file |
Configuration Error |
|
626 |
Cannot load a string |
Unknown |
|
627 |
Cannot find key |
Configuration Error |
|
628 |
The port was disconnected |
Modem Problem |
|
629 |
The port was disconnected by the remote computer |
Modem Problem |
|
630 |
The port was disconnected due to hardware failure |
User Error |
|
631 |
The port was disconnected by the user |
User Error |
|
632 |
The structure size is incorrect |
Unknown |
|
633 |
The port is already in use or is not Configurationured for Dial-Up Networking |
Configuration Error |
|
634 |
Cannot register your computer on the remote network |
Login Problem |
|
635 |
Unknown error or user cancelled authentication prompt |
User Error |
|
636 |
The wrong device is attached to the port |
Configuration Error |
|
637 |
The string could not be converted |
Unknown |
|
638 |
The request has timed out |
Unknown |
|
639 |
No asynchronous net available |
Unknown |
|
640 |
A NetBIOS error has occurred |
Login Problem |
|
641 |
The server cannot allocate NetBIOS resources needed to support the client |
Login Problem |
|
642 |
One of your NetBIOS names is already registered on the remote network |
Configuration Error |
|
643 |
A network adapter at the server failed |
Login Problem |
|
644 |
You will not receive network message popups |
Configuration Error |
|
645 |
Internal authentication error or dial-up adaptor not Configurationured to use TCP |
Configuration Error |
|
646 |
The account is not permitted to log on at this time of day |
User Error |
|
647 |
The account is disabled |
User Error |
|
648 |
The password has expired |
User Error |
|
649 |
The account does not have Dial-Up Networking permission |
Configuration Error |
|
650 |
The Dial-Up Networking server is not responding |
Login Problem |
|
651 |
Your modem or other connecting device has reported an error |
Configuration Error |
|
652 |
Unrecognized response from the device |
Configuration Error |
|
653 |
A macro required by the device was not found in the device INF file |
Configuration Error |
|
654 |
A command or response in the device INF file contains an undefined macro |
Configuration Error |
|
655 |
The <message> macro was not found in the device INF file secion |
Configuration Error |
|
656 |
The <defaultoff> macro in the device INF file contains an undefined macro |
Configuration Error |
|
657 |
The device INF file could not be opened |
Configuration Error |
|
658 |
The device name in the device INF or media INI file is too long |
Configuration Error |
|
659 |
The media INI file refers to an unknown device name |
Configuration Error |
|
660 |
The device INF file contains no responses for the command |
Configuration Error |
|
661 |
The device INF file is missing a command |
Configuration Error |
|
662 |
Attempted to set a macro not listed in device INF file section |
Configuration Error |
|
663 |
The media INI file refers to an unknown device type |
Configuration Error |
|
664 |
Cannot allocate memory |
Unknown |
|
665 |
The port is not Configurationured for Dial-Up Networking |
Configuration Error |
|
666 |
Your modem or other connecting device is not functioning |
Configuration Error |
|
667 |
Cannot read the media INI file |
Configuration Error |
|
668 |
The connection dropped |
Modem Problem |
|
669 |
The usage parameter in the media INI file is invalid |
Configuration Error |
|
670 |
Cannot read the section name from the media INI file |
Configuration Error |
|
671 |
Cannot read the device type from the media INI file |
Configuration Error |
|
672 |
Cannot read the device name from the media INI file |
Configuration Error |
|
673 |
Cannot read the usage from the media INI file |
Configuration Error |
|
674 |
Cannot read the maximum connection BPS rate from the media INI file |
Configuration Error |
|
675 |
Cannot read the maximum carrier BPS rate from the media INI file |
Configuration Error |
|
676 |
Line busy |
Busy |
|
677 |
A person answered instead of a modem |
User Error |
|
678 |
There is no answer |
No Answer |
|
679 |
Cannot detect carrier |
User Error |
|
680 |
There is no dial tone |
User Error |
|
681 |
General error reported by device |
Unknown |
|
682 |
Error writing section name |
Configuration Error |
|
683 |
Error writing device type |
Configuration Error |
|
684 |
Error writing device name |
Configuration Error |
|
685 |
Error writing max connect BPS |
Configuration Error |
|
686 |
Error writing max carrier BPS |
Configuration Error |
|
687 |
Error writing usage |
Configuration Error |
|
688 |
Error writing defaultoff |
Configuration Error |
|
689 |
Error reading defaultoff |
Configuration Error |
|
690 |
Empty INI file |
Configuration Error |
|
691 |
Access denied because username and/or password is invalid on the domain |
User Error |
|
692 |
Hardware failure in port or attached device |
User Error |
|
693 |
Not binary macro |
Configuration Error |
|
694 |
DCB not found |
Configuration Error |
|
695 |
State machines not started |
Unknown |
|
696 |
State machines already started |
Unknown |
|
697 |
Partial response looping |
Unknown |
|
698 |
A response keyname in the device INF file is not in the expected format |
Configuration Error |
|
699 |
The device response caused buffer overflow |
Unknown |
|
700 |
The expanded command in the device INF file is too long |
Configuration Error |
|
701 |
The device moved to a BPS rate not supported by the COM driver |
Configuration Error |
|
702 |
Device response received when none expected |
Configuration Error |
|
703 |
Interactive mode |
Configuration Error |
|
704 |
Bad callback number |
Configuration Error |
|
705 |
Invalid auth state |
Unknown |
|
706 |
Error writing init BPS |
Configuration Error |
|
707 |
X25 diagnostic indication |
Unknown |
|
708 |
The account has expired |
User Error |
|
709 |
Error changing password on domain. Try again |
Login Problem |
|
710 |
Serial overrun errors were detected while communicating with your modem |
Modem Problem |
|
711 |
RasMan initialization failure. Check the event log |
Unknown |
|
712 |
Biplex port initializing. Wait a few seconds and redial |
User Error |
|
713 |
No active ISDN lines |
Configuration Error |
|
714 |
No active ISDN lines are available |
Configuration Error |
|
715 |
Too many errors occurred because of poor phone line quality |
Modem Problem |
|
716 |
Error IP Configurationuration |
Configuration Error |
|
717 |
No IP addresses |
Configuration Error |
|
718 |
PPP timeout |
Login Problem |
|
719 |
PPP remote terminated |
Login Problem |
|
720 |
PPP no compatible protocols Configurationured |
Login Problem |
|
721 |
PPP no response |
Login Problem |
|
722 |
PPP invalid packet |
Login Problem |
|
723 |
Phone number too long |
Configuration Error |
|
724 |
IPXCP no dialout Configurationured |
Configuration Error |
|
725 |
IPXCP no dialin Configurationured |
Configuration Error |
|
726 |
IPXCP dialout already active |
Configuration Error |
|
727 |
Error accessing tcpcfg dll |
Configuration Error |
|
728 |
No IP RAS adapter |
Configuration Error |
|
729 |
SLIP requires IP |
Configuration Error |
|
730 |
Projection not complete |
Login Problem |
|
731 |
PPP protocol not Configurationured |
Login Problem |
|
732 |
PPP not converging |
Login Problem |
|
733 |
PPP CP rejected |
Login Problem |
|
734 |
PPP ICP terminated |
Login Problem |
|
735 |
PPP required address rejected |
Login Problem |
|
736 |
PPP NCP terminated |
Login Problem |
|
737 |
PPP loopback detected |
Login Problem |
|
738 |
PPP no address assigned |
Login Problem |
|
739 |
Cannot use logon credentials |
Login Problem |
|
740 |
Error TAPI Configurationuration |
Configuration Error |
|
741 |
No local encryption |
Configuration Error |
|
742 |
No remote encryption |
Configuration Error |
|
743 |
Remote requires encryption |
Configuration Error |
|
744 |
IPXCP net number conflict |
Configuration Error |
|
745 |
The Session Management Module is invalid |
Configuration Error |
|
746 |
The Session Management Module is not initialized |
Configuration Error |
|
747 |
The MAC is not available for this connection |
Configuration Error |
|
748 |
The session cannot be established in time |
Login Problem |
|
749 |
The device cannot dial the phone number |
Configuration Error |
|
750 |
The incorrect authentication module |
Configuration Error |
|
751 |
Invalid dialback Configuration number |
Configuration Error |
|
752 |
Invalid dialup script syntax |
Configuration Error |
|
2100 |
Wrong Configuration entry size |
Unknown |
|
2101 |
Unable to save Configurationuration changes |
Configuration Error |
|
2102 |
Unable to set upload flag |
Configuration Error |
|
2103 |
AccessRamp is installed incorrectly |
Unknown |
|
2104 |
Unable to create window |
Unknown |
|
2105 |
Low system resources |
Unknown |
|
2106 |
Dialer not responding |
Unknown |
|
2107 |
Unable to open log file for writing |
Unknown |
|
2108 |
Failed to write to log file |
Unknown |
|
2109 |
Insufficient system resources |
Unknown |
|
2110 |
Dialer did not respond correctly |
Unknown |
|
2200 |
User cancelled |
User Error |
|
2201 |
AccessRamp initialization failed |
Configuration Error |
|
2202 |
Bad Configurationuration detected |
Configuration Error |
|
2205 |
The handle is invalid |
Unknown |
|
2206 |
Not enough memory is available |
Configuration Error |
|
2207 |
Unknown system error code |
Unknown |
|
2208 |
Invalid parameter |
Unknown |
|
2209 |
Please restart Windows |
Unknown |
|
2210 |
The password cache has been repaired (not an error) |
Success |
|
2211 |
Unable to load AWAOL.DLL |
Configuration Error |
|
2212 |
Dial-Up Networking is not installed |
Configuration Error |
|
2213 |
Dial-Up Adapter is not installed |
Configuration Error |
|
2214 |
Microsoft TCP/IP protocol is not installed |
Configuration Error |
|
2215 |
Dial-Up Adapter is not binded to Microsoft TCP/IP protocol |
Configuration Error |
|
2216 |
Unknown phone number (internal error) |
Unknown |
|
2217 |
Test aborted (internal error) |
Unknown |
|
2218 |
Could not open log file (internal error) |
Unknown |
|
2219 |
Could not write to log file (internal error) |
Unknown |
|
2220 |
Corrupted password cache file deleted (internal error) |
Unknown |
|
2221 |
Windows restarting (internal error) |
Unknown |
|
2222 |
System restarting (internal error) |
Unknown |
|
2260 AOL |
The account is already in use |
Login Problem |
|
2261 AOL |
Already online |
User Error |
|
2262 AOL |
An AOL exception has occurred |
Unknown |
|
2263 AOL |
The modem received a busy signal |
Busy |
|
2264 AOL |
Request canceled |
User Error |
|
2265 AOL |
Thread creation failed |
Unknown |
|
2265 AOL |
Unable to disconnect from AOL |
Unknown |
|
2267 AOL |
Unable to load LAUNCH32.DLL |
Configuration Error |
|
2268 AOL |
A connection is already in progress |
User Error |
|
2269 AOL |
A scheduled session was interrupted by a modal dialog box |
Unknown |
|
2270 AOL |
The modem could not detect a carrier |
User Error |
|
2271 AOL |
Unable to establish a connection to AOL |
Login Problem |
|
2272 AOL |
The modem was unable to detect a dial tone |
User Error |
|
2273 AOL |
AOL client software is not fully installed and registered |
Configuration Error |
|
2274 AOL |
System error |
Unknown |
|
2275 AOL |
Unknown error | |
|
2275 AOL |
Unknown error |
Unknown |
|
2276 AOL |
AOL client was unable to initialize modem |
Configuration Error |
|
2277 AOL |
AOL client was unable to open COM port |
User Error |
|
228 AOL |
AOL path not supplied or detected |
Configuration Error |
|
2281 AOL |
AOL command line too long |
Configuration Error |
|
2282 AOL |
AOL client software corrupted |
Unknown |
|
2283 AOL |
AOL function call failed |
Unknown |
|
2284 AOL |
AOL file not found |
Configuration Error |
|
2285 AOL |
A modal dialog generated by the AOL client is awaiting input |
Unknown |
|
2286 AOL |
AOL client software is a newer version than is supported by LAUNCH32 |
Configuration Error |
|
2288 AOL |
AOL client software is an older version than is supported by LAUNCH32 |
Configuration Error |
|
2289 AOL |
Insufficient memory |
Unknown |
|
2290 AOL |
The AOL database is not compatible with LAUNCH32.DLL |
Configuration Error |
|
2291 AOL |
AOL reports that the user has canceled the request |
User Error |
|
2292 AOL |
Waiting for the AOL installer to return |
Unknown |
|
2299 AOL |
An AOL function in LAUNCH32.DLL returned an unrecognized value |
Unknown |
|
Search Keywords |
| |
|
Hint Category |
Error Messages, Communications Software | |
|
Date Created |
30-09-98 | |
|
Last Updated |
10-03-99 | |
|
Revision Date |
10-03-2000 | |
|
Brand |
IBM Aptiva | |
|
Product Family |
Aptiva | |
|
Machine Type |
2134, 2136, 2137, 2138, 2139, 2140, 2142, 2144, 2153, 2156, 2158, 2159, 2161, 2162, 2163, 2164, 2168, 2176 | |
|
Model |
all | |
|
TypeModel |
| |
|
Retain Tip (if applicable) |
| |
|
Reverse Doclinks |