T55A 15" TFT LCD Color Monitor - Technical Specifications

34.265 bytes

Product Information

Document ID: VLAR-3XVN6U

T55A 15" TFT LCD Color Monitor - Technical Specifications

Applicable to: World-Wide

This document contains feature and technical specification information for the: IBM 9513 15" TFT LCD Color Monitor.

Technical Characteristics:

LCD Size and Type

15.0-in TFT

Viewable Image Size (in/mm)

15.0 / 381

Max Viewable Area (mm)

304.1 x 228.1

Luminance (@ 100 Hrs )

200 cd/m2

Contrast

150:01:00

Colors (6 Bit Drivers + Dither)

16.7-million

Viewing Angle ( 10:1 Contrast )

Horiz = +/-50 , Vert = +/-45 degrees

Chromaticity CIE (x,y)

Red = 0.606, 0.348
Blue = 0.149, 0.360
Green = 0.309, 0.507
White = 0.293, 0.310

Cell Response Time

50. ms

RGB Vert Stripe Pixel pitch (mm)

0.297

Anti-reflective

< 2.0%

Multi-frequency operation

Yes

Horizontal Frequency (kHz)

30 - 61

Vertical Frequency (Hz)

56 - 75

Non-Interlace Video

Yes (all modes)

Video Input (Max) 110 MHz

1024 x 768 @ 75Hz

Corresponding Screen Refresh

1024 x 768 @ 60Hz

Signal cable - detachable

1.8 m

Video

RGB Analogue + separate H&V Syncs

Sync Type 1

Separate H&V sync

Sync Polarity

Positive or Negative

Video connector

15-pin D-Sub

Video Signal Levels

0.700 V p-p

Video Signal Polarity

Positive = Bright

Video Signal Impedance

75 Ohms +/-5% (terminated)

Sync Type 1 Signal Levels

TTL ( High >2.0V, Low <0.8V )

Sync Termination

>2 KOhms

Sync Type 2

Composite sync

Sync Type 3

Sync on green

Sync Type 3 Signal Levels

0.3 V

Sync Polarity

Negative only

User controls

Digital

Lockable controls

Yes

On Screen Display (OSD)

Yes

OSD Languages

5

Factory-preset display modes

10

User display mode settings

10

VESA DDC capable

2B

Apple attach capable

Yes ( with suitable dongle )

ISO 13406 Pt2 capable

Yes

VESA DPMS power mgmt capable

Yes

Power supply

Universal

Power cord - detached

1.8 m

JEIDA compliance

Yes

FCC B compliance

Yes

MPR-2 Emission compliance

Yes

MPR-3 Emission compliance

Yes

TCO92 Compliant

Yes

TCO95 Environmental Label

Yes

Tilt-swivel base

Detachable

Forward tilt (degrees)

-4

Backward tilt (degrees)

+41

Dimensions:

Width

16.3-in (413.0 mm)

Depth

8.1-in (204.3 mm)

Height

15.0-in (380.6 mm) Includes the tilting stand.

Weight

14.3 lb ( 6.5 kg) Includes the tilting stand.

Dimensions and weight of the monitor and stand(unpacked).

Ambient Temperature and Relative Humidity

Parameter

Temperature

Relative Humidity

Altitude

Operating

10 to 35 deg.C

10 to 80 %

0 to 6,500-ft ( 2,000 m)

Shipping

-20 to 60 deg.C

5 to 95 %

0 to 49,200-ft (15,000 m)

Storage

-20 to 60 deg.C

5 to 95 %

0 to 6,500-ft ( 2,000 m)

Compatibility:
Video Adapters
The T55A color monitor has been tested for compatibility with the following PC Video Adapter Cards:

Manufacturer

Video Adpter Card

Video Chip Set

ATI

Xpert@Work

ATI Rage Pro

ATI

All-In-Wonder

ATI Rage II+DVD

Asus

3D Explorer 300

nVidia Riva 128

Diamond

Stealth II S220

Rendition V2100

ELSA

Gloria Synergy

3D Labs Permedia 2

Hercules

Terminator 3D/DX

S3 Virge DX

Leadtek

WinFast 3D L230

3D Labs Permedia 2

Matrox

Millennium

MGA

Matrox

Millennium II

MGA

Matrox

Mystique

MGA

Number 9

FX Reality 334

S3 Virge/GX2

Number 9

FX Reality 772

S3 Virge/VX

STB

Velocity 3D

S3 Virge/VX

Trident

4MB SGRAM AGP

Trident 3D Image 9750

Video Logic

Apocalypse

ET6100

Systems:
The T55A color monitor is supplied with a detachable 1.8 meter video signal cable. This cable has the same 15-pin, D-Sub video connector for system unit connection as previous IBM general purpose monitors. The T55A color monitor has been tested for compatibility with the following PC systems:

System

Machine Type

Video Chip Set

IBM PC 365

6589

Matrox Millenium

IBM PC 300 GL

6282

Cirrus GD-5446

IBM PC 300 XL

6588

S3 Trio 64V2

IBM PC 300 PL

6562

MGA

IBM PC 300 GL

6561

Cirrus 5465 AGP

IBM PC 300 PL

6862

S3 Trio 3D

IBM PC

*

*

IBM IntelliStation Z Pro

6899

Intergraph Intense 3D 1000

IBM IntelliStation M Pro

6898-100

Permedia II AGP

IBM IntelliStation M Pro

6898-140

Intergraph Intense 3D 3000

IBM IntelliStation M Pro

6898-

Matrox Millenium II AGP

IBM Aptiva

2137

ATI 3D Rage 2+

IBM Aptiva ( Jaws 4 )

*

*

IBM Aptiva ( Cobra )

*

*

Non-IBM System Units

*

*

IBM Network Station

8361

S3 Trio 64V+

IBM RS/6000 Workstation

IBM Power Series of Graphics Adapters for RS/6000:
Gt3i, Gt4, Gt4x, Gt4e, Gt4i, Gt4xi
GXT110P, GXT150, GXT150M, GXT150L,GXT150P
GXT250P/255P, GXT500/500D, GXT500P/550P, GXT800P, GXT1000
E15/S15 Graphics Adapters

Sun and HP Workstations

*

*

Hardware Requirements:
The T55A color monitor is designed to operate with system units or video adapters that generate a video output signal that falls within the specifications below:

Maximum addressability (pixels)

1024 x 768

Maximum pixel rate (MHz)

110

Horizontal frequency (kHz)

30 - 61

Vertical frequency (Hz)

50 - 75

National language support is a function of the video adapter in the system unit and the application or support software.

Software Requirements:
The T55A color monitor features factory-preset and user-settable display modes. The actual display modes used depend upon the attaching system unit, the operating system, and application software.

Power Requirements:

Input voltage

90 - 260 V AC

Frequency

50 / 60 Hz

Heat dissipation (Maximum)

136 Btu/Hr

Power consumption (Maximum)

40 watts

Power consumption (Normal use)

< 40 watts typical

Power consumption (VESA Standby)

5 watts maximum

Power consumption (VESA Suspend)

5 watts maximum

Power consumption (VESA Off)

5 watts maximum

Current Leakage

Maximum:
< 3.5 mA @ 260 V
< 2.5 mA @ 100 V

Actual power consumption depends upon the chosen display mode, the images displayed, and user control settings.

Staged monitor power shutdown is controlled by the state of the H- and V-sync lines on the incoming video signal as follows:

Stage

H-Sync

V-Sync

Monitor Status

VESA State

T55A Power

1

Active

Active

Normal Operation

On

< 40. Watts

2

Inactive

Active

Video Off
- Screen blank
- Instant restart

Standby

< 5. Watts

3

Active

Inactive

Video, Scans Off
- Screen blank
- Instant restart

Suspend

< 5. Watts

4

Inactive

Inactive

Off except for microprocessor
- Screen blank
- Delayed restart

Off

< 5. Watts

Factory-Preset PC Display Modes:
The factory-preset modes cannot be overwritten, but can be adjusted to personal choice. The new settings are stored automatically in one of the user locations and are recalled each time that mode is used. The factory settings for the mode in use, if any, can be restored by operating the Geometry Reset/Recall control. It may be necessary to make some adjustments to the displayed image to compensate for variations in video signal timings. The user controls can be used to make these adjustments. Information about the current display mode is shown in the on-screen displays.

Addressability

Incoming Video

Screen Refresh

720 x 400

70 Hz NI (Non-interlaced)

60.0 Hz

640 x 350

70 Hz NI (Non-interlaced)

60.0 Hz

832 x 624

75 Hz NI (Non-interlaced)

60.0 Hz

640 x 480

60 Hz NI (Non-interlaced)

60.0 Hz

640 x 480

75 Hz NI (Non-interlaced)

60.0 Hz

800 x 600

60 Hz NI (Non-interlaced)

60.0 Hz

800 x 600

75 Hz NI (Non-interlaced)

60.0 Hz

1024 x 768

60 Hz NI (Non-interlaced)

60.0 Hz

1024 x 768

70 Hz NI (Non-interlaced)

60.0 Hz

1024 x 768

75 Hz NI (Non-interlaced)

60.0 Hz

There are 10 total factory presets and 10 user locations available.

Ergonomics and Agency Approvals:

Acoustics:

Declared acoustical noise emissions LWAD = 3.7 Bels or less.

The noise emission level stated is the declared (upper limit) A-weighted sound power level, in Bels, for a random sample of monitors. All measurements are made in accordance with ANSI S12.10 and reported in conformance with ISO 9296.

Emissions:

All models meet the emmission category B requirements of Swedish Standard SS-436-14-90 ("MPR-3") in addition to those of MPR-2.

All models meet the Swedish Board for Technical Accreditation (SWEDAC) emission guidelines contained in MPR 1990:10 when tested using the MPR 1990:08 test method.

The monitors also meet the TCO95 Environmental Label from the Swedish Confederation of Professional Employees (TCO), and the emission, power management, and electrical safety requirements of the TCO95 Environmental Label.

Ergonomics:

Compliance to the International Organization for Standardization (ISO) 13406 Pt 2 for improved ergonomics and image quality is provided when the monitor forms part of an ISO-compliant system.

Regulatory
Agency
Approvals:

UL (U.S.)
CSA (Canada)
IEC950 CB Report
TUV EN 60950 (Germany)
NEMKO (Norway)
Korean Safety Reg No 776
SEMKO (Sweden)
DEMKO (Denmark)
FIMKO (Finland)
CCIB/CCEE (China)
NOM (Mexico)
SASO (Saudi Arabia)
CE (Europe)
GOST (Russia)
SISIR (Singapore)
MEEI (Hungary)
PCBC (Poland)
EZU (Czech)
FCC B (U.S.) (A3KM078)
IC (Canada)
CE (Europe)
EN 55022 B (Europe)
EN 50081 B (Europe)
VCCI (Japan)
Korea EMI Reg No 825
Australia
New Zealand
South Africa SABS
BCIQ (Taiwan)

Environmental,
Energy,
Ergonomic,
Compatibility Approvals:

MPR-2 (Sweden)
MPR-3 (Sweden)
TCO95 (Sweden)
NUTEK (Sweden)
ENERGY STAR (U.S.)
GS (Germany) ZH1/618/10.80
ISO 9241 Pt 3
ISO 9241 Pt 8
ISO 13406 Pt 2 ( Target )
Windows** 95/98

** Trademark of Microsoft Corporation.

OSD Controls
Digital user controls are located on the front bezel, to the left of the power on/off pushbutton. Adjustments are made in conjunction with the on-screen displays. After adjustments are made, the controls can be locked to prevent further changes. With exception of Brightness & Contrast all the controls are lockable.

Control

T55A Monitor

Auto Setup

Y

Coarse Clock for FOS adjust

Y

Fine Clock for FOS adjust

Y

Brightness (not lockable )

Y

Contrast (not lockable)

Y

Screen Expansion on/off

Y

Image Horizontal position

Y

Image Vertical position

Y

Geometry reset/recall

Y

OSD Language selection

Y (1)

OSD Menu Position

Y

OSD information : Video Mode

Y

OSD Horizontal position

Y

OSD Vertical position

Y

OSD Information....Mode Data

Y

Preset color selection

3 Modes

R,G,B gain adjustment

Y

Color point recall

Y

Controls lock/unlock

Y

(1) Languages available in the OSD are English, French, German, Italian and Spanish.

Indicators
The power indicator LED indicates the operational state of the monitor:

Indicator

T55A Operating State

Power Use

Steady green

Normal operation

<40 Watts

Steady amber

DPMS - Standby state

< 5 Watts

Amber blink @ 0.5Sec

DPMS - Suspend state

< 5 Watts

Amber blink @ 1.0Sec

DPMS - Off state

< 5 Watts

A 'No Connection / Check signal cable' message appears in the OSD whenever the monitor detects no incoming video signal. Whenever the monitor detects a video signal that is outside its operating range the LED will flash at a rate, specified in the "User Guide" to indicate that there is a problem.

Limitations:

Supported display modes are a function of the attaching system unit. The full range of display modes available with these monitors may not be available or supported with all combinations of system units, their operating systems, and application software.

Horizontal and vertical sync signal timings are critical in order to achieve acceptable screen images. As a consequence, support for all possible variations in H- and V-sync timings for any display mode cannot be assumed.

Adjustment of the user controls to enlarge the image to its maximum size requires that the signal timings of the display mode being used fall within the monitor timing specifications.

The number of colors shown in any display mode (max = 16.7 million) is not limited by the monitor, but depends upon the capabilities of the video adapter in the system unit.

The T55A provides FCC class B - residential installation - compliance in all display modes

Implementation of monitor power management follows the Video Electronics Standards Association (VESA) Display Power Management Signaling (DPMS) standard. This standard must also be implemented in the attaching system unit hardware and software for monitor power management to be effective. The system implementation must provide user-adjustable, power-down delay periods. The monitor power management function is invoked only after appropriate signals are received from an attached system unit or video adapter.

Implementation of monitor Plug and Play follows the VESA Display Data Channel (DDC) standard. This standard must also be implemented in the attaching system unit hardware and software for monitor Plug and Play to be effective.

Certain functions require the system unit to be similarly configured, so all monitor functions may not be enabled when attached to a particular system unit.

Document Note(s):

1.

The symbols, * and [*], are used to denote that the information is currently unavailable for this product.

2.

N/A is used to denote that there is no applicable information for this product.

3.

Multiple ordering information gives the partnumber that can be used to order the product in bulk.

4.

Geo is used to denote the Geography to which the information is applicable.

5.

All dates are represented in the US English format of mm/dd/yyyy (where mm=month, dd=day, yyyy=year).

6.

Effective Withdrawal means that on the given date IBM will have withdrawn the products from marketing. After that date, customers will no longer be able to obtain the product(s) directly from IBM.

Search Keywords

Document Category

Technical Specifications

Date Created

31-08-98

Last Updated

20-01-99

Revision Date

20-01-2000

Brand

IBM Monitors

Product Family

Flat Panel

Machine Type

9513

Model

AW1; AG1

TypeModel

Retain Tip (if applicable)

Reverse Doclinks
and Admin Purposes

	LCD Size and Type	15.0-in TFT
	Viewable Image Size (in/mm)	15.0 / 381
	Max Viewable Area (mm)	304.1 x 228.1
	Luminance (@ 100 Hrs )	200 cd/m2
	Contrast	150:01:00
	Colors (6 Bit Drivers + Dither)	16.7-million
	Viewing Angle ( 10:1 Contrast )	Horiz = +/-50 , Vert = +/-45 degrees
	Chromaticity CIE (x,y)	Red = 0.606, 0.348 Blue = 0.149, 0.360 Green = 0.309, 0.507 White = 0.293, 0.310
	Cell Response Time	50. ms
	RGB Vert Stripe Pixel pitch (mm)	0.297
	Anti-reflective	< 2.0%
	Multi-frequency operation	Yes
	Horizontal Frequency (kHz)	30 - 61
	Vertical Frequency (Hz)	56 - 75
	Non-Interlace Video	Yes (all modes)
	Video Input (Max) 110 MHz	1024 x 768 @ 75Hz
	Corresponding Screen Refresh	1024 x 768 @ 60Hz
	Signal cable - detachable	1.8 m
	Video	RGB Analogue + separate H&V Syncs
	Sync Type 1	Separate H&V sync
	Sync Polarity	Positive or Negative
	Video connector	15-pin D-Sub
	Video Signal Levels	0.700 V p-p
	Video Signal Polarity	Positive = Bright
	Video Signal Impedance	75 Ohms +/-5% (terminated)
	Sync Type 1 Signal Levels	TTL ( High >2.0V, Low <0.8V )
	Sync Termination	>2 KOhms
	Sync Type 2	Composite sync
	Sync Type 3	Sync on green
	Sync Type 3 Signal Levels	0.3 V
	Sync Polarity	Negative only
	User controls	Digital
	Lockable controls	Yes
	On Screen Display (OSD)	Yes
	OSD Languages	5
	Factory-preset display modes	10
	User display mode settings	10
	VESA DDC capable	2B
	Apple attach capable	Yes ( with suitable dongle )
	ISO 13406 Pt2 capable	Yes
	VESA DPMS power mgmt capable	Yes
	Power supply	Universal
	Power cord - detached	1.8 m
	JEIDA compliance	Yes
	FCC B compliance	Yes
	MPR-2 Emission compliance	Yes
	MPR-3 Emission compliance	Yes
	TCO92 Compliant	Yes
	TCO95 Environmental Label	Yes
	Tilt-swivel base	Detachable
	Forward tilt (degrees)	-4
	Backward tilt (degrees)	+41
Dimensions:	Width	16.3-in (413.0 mm)
	Depth	8.1-in (204.3 mm)
	Height	15.0-in (380.6 mm) Includes the tilting stand.
	Weight	14.3 lb ( 6.5 kg) Includes the tilting stand.

Parameter	Temperature	Relative Humidity	Altitude
Operating	10 to 35 deg.C	10 to 80 %	0 to 6,500-ft ( 2,000 m)
Shipping	-20 to 60 deg.C	5 to 95 %	0 to 49,200-ft (15,000 m)
Storage	-20 to 60 deg.C	5 to 95 %	0 to 6,500-ft ( 2,000 m)

Manufacturer	Video Adpter Card	Video Chip Set
ATI	Xpert@Work	ATI Rage Pro
ATI	All-In-Wonder	ATI Rage II+DVD
Asus	3D Explorer 300	nVidia Riva 128
Diamond	Stealth II S220	Rendition V2100
ELSA	Gloria Synergy	3D Labs Permedia 2
Hercules	Terminator 3D/DX	S3 Virge DX
Leadtek	WinFast 3D L230	3D Labs Permedia 2
Matrox	Millennium	MGA
Matrox	Millennium II	MGA
Matrox	Mystique	MGA
Number 9	FX Reality 334	S3 Virge/GX2
Number 9	FX Reality 772	S3 Virge/VX
STB	Velocity 3D	S3 Virge/VX
Trident	4MB SGRAM AGP	Trident 3D Image 9750
Video Logic	Apocalypse	ET6100

System	Machine Type	Video Chip Set
IBM PC 365	6589	Matrox Millenium
IBM PC 300 GL	6282	Cirrus GD-5446
IBM PC 300 XL	6588	S3 Trio 64V2
IBM PC 300 PL	6562	MGA
IBM PC 300 GL	6561	Cirrus 5465 AGP
IBM PC 300 PL	6862	S3 Trio 3D
IBM PC	*	*
IBM IntelliStation Z Pro	6899	Intergraph Intense 3D 1000
IBM IntelliStation M Pro	6898-100	Permedia II AGP
IBM IntelliStation M Pro	6898-140	Intergraph Intense 3D 3000
IBM IntelliStation M Pro	6898-	Matrox Millenium II AGP
IBM Aptiva	2137	ATI 3D Rage 2+
IBM Aptiva ( Jaws 4 )	*	*
IBM Aptiva ( Cobra )	*	*
Non-IBM System Units	*	*
IBM Network Station	8361	S3 Trio 64V+
IBM RS/6000 Workstation		IBM Power Series of Graphics Adapters for RS/6000: Gt3i, Gt4, Gt4x, Gt4e, Gt4i, Gt4xi GXT110P, GXT150, GXT150M, GXT150L,GXT150P GXT250P/255P, GXT500/500D, GXT500P/550P, GXT800P, GXT1000 E15/S15 Graphics Adapters
Sun and HP Workstations	*	*

Maximum addressability (pixels)	1024 x 768
Maximum pixel rate (MHz)	110
Horizontal frequency (kHz)	30 - 61
Vertical frequency (Hz)	50 - 75

Input voltage	90 - 260 V AC
Frequency	50 / 60 Hz
Heat dissipation (Maximum)	136 Btu/Hr
Power consumption (Maximum)	40 watts
Power consumption (Normal use)	< 40 watts typical
Power consumption (VESA Standby)	5 watts maximum
Power consumption (VESA Suspend)	5 watts maximum
Power consumption (VESA Off)	5 watts maximum
Current Leakage	Maximum: < 3.5 mA @ 260 V < 2.5 mA @ 100 V

Stage	H-Sync	V-Sync	Monitor Status	VESA State	T55A Power
1	Active	Active	Normal Operation	On	< 40. Watts
2	Inactive	Active	Video Off - Screen blank - Instant restart	Standby	< 5. Watts
3	Active	Inactive	Video, Scans Off - Screen blank - Instant restart	Suspend	< 5. Watts
4	Inactive	Inactive	Off except for microprocessor - Screen blank - Delayed restart	Off	< 5. Watts

Addressability	Incoming Video	Screen Refresh
720 x 400	70 Hz NI (Non-interlaced)	60.0 Hz
640 x 350	70 Hz NI (Non-interlaced)	60.0 Hz
832 x 624	75 Hz NI (Non-interlaced)	60.0 Hz
640 x 480	60 Hz NI (Non-interlaced)	60.0 Hz
640 x 480	75 Hz NI (Non-interlaced)	60.0 Hz
800 x 600	60 Hz NI (Non-interlaced)	60.0 Hz
800 x 600	75 Hz NI (Non-interlaced)	60.0 Hz
1024 x 768	60 Hz NI (Non-interlaced)	60.0 Hz
1024 x 768	70 Hz NI (Non-interlaced)	60.0 Hz
1024 x 768	75 Hz NI (Non-interlaced)	60.0 Hz

Acoustics:	Declared acoustical noise emissions LWAD = 3.7 Bels or less. The noise emission level stated is the declared (upper limit) A-weighted sound power level, in Bels, for a random sample of monitors. All measurements are made in accordance with ANSI S12.10 and reported in conformance with ISO 9296.
Emissions:	All models meet the emmission category B requirements of Swedish Standard SS-436-14-90 ("MPR-3") in addition to those of MPR-2. All models meet the Swedish Board for Technical Accreditation (SWEDAC) emission guidelines contained in MPR 1990:10 when tested using the MPR 1990:08 test method. The monitors also meet the TCO95 Environmental Label from the Swedish Confederation of Professional Employees (TCO), and the emission, power management, and electrical safety requirements of the TCO95 Environmental Label.
Ergonomics:	Compliance to the International Organization for Standardization (ISO) 13406 Pt 2 for improved ergonomics and image quality is provided when the monitor forms part of an ISO-compliant system.
Regulatory Agency Approvals:	UL (U.S.) CSA (Canada) IEC950 CB Report TUV EN 60950 (Germany) NEMKO (Norway) Korean Safety Reg No 776 SEMKO (Sweden) DEMKO (Denmark) FIMKO (Finland) CCIB/CCEE (China) NOM (Mexico) SASO (Saudi Arabia) CE (Europe) GOST (Russia) SISIR (Singapore) MEEI (Hungary) PCBC (Poland) EZU (Czech) FCC B (U.S.) (A3KM078) IC (Canada) CE (Europe) EN 55022 B (Europe) EN 50081 B (Europe) VCCI (Japan) Korea EMI Reg No 825 Australia New Zealand South Africa SABS BCIQ (Taiwan)
Environmental, Energy, Ergonomic, Compatibility Approvals:	MPR-2 (Sweden) MPR-3 (Sweden) TCO95 (Sweden) NUTEK (Sweden) ENERGY STAR (U.S.) GS (Germany) ZH1/618/10.80 ISO 9241 Pt 3 ISO 9241 Pt 8 ISO 13406 Pt 2 ( Target ) Windows** 95/98

Control	T55A Monitor
Auto Setup	Y
Coarse Clock for FOS adjust	Y
Fine Clock for FOS adjust	Y
Brightness (not lockable )	Y
Contrast (not lockable)	Y
Screen Expansion on/off	Y
Image Horizontal position	Y
Image Vertical position	Y
Geometry reset/recall	Y
OSD Language selection	Y (1)
OSD Menu Position	Y
OSD information : Video Mode	Y
OSD Horizontal position	Y
OSD Vertical position	Y
OSD Information....Mode Data	Y
Preset color selection	3 Modes
R,G,B gain adjustment	Y
Color point recall	Y
Controls lock/unlock	Y

Indicator	T55A Operating State	Power Use
Steady green	Normal operation	<40 Watts
Steady amber	DPMS - Standby state	< 5 Watts
Amber blink @ 0.5Sec	DPMS - Suspend state	< 5 Watts
Amber blink @ 1.0Sec	DPMS - Off state	< 5 Watts

1.	The symbols, * and [*], are used to denote that the information is currently unavailable for this product.
2.	N/A is used to denote that there is no applicable information for this product.
3.	Multiple ordering information gives the partnumber that can be used to order the product in bulk.
4.	Geo is used to denote the Geography to which the information is applicable.
5.	All dates are represented in the US English format of mm/dd/yyyy (where mm=month, dd=day, yyyy=year).
6.	Effective Withdrawal means that on the given date IBM will have withdrawn the products from marketing. After that date, customers will no longer be able to obtain the product(s) directly from IBM.

	Search Keywords
	Document Category	Technical Specifications
	Date Created	31-08-98
	Last Updated	20-01-99
	Revision Date	20-01-2000
	Brand	IBM Monitors
	Product Family	Flat Panel
	Machine Type	9513
	Model	AW1; AG1
	TypeModel
	Retain Tip (if applicable)
	Reverse Doclinks and Admin Purposes