21.917 bytes

Service Hints & Tips

Document ID: LWIK-3XNHMK

TP 560Z - Installing Windows 95 and its device drivers

Applicable to: World-Wide

This document describes the installation procedures for Windows 95 and its software for your ThinkPad computer.

The following versions of Windows 95 are available for your computer:
Service Pack Version 1 (OSR1)
OEM Service Release Version 2.1 (OSR2.1)
OSR1 can be downloaded Windows 95 from the Microsoft Internet home page (http://www.microsoft.com).

Your Version of Windows 95
You can check which version of Windows 95 you are using as follows:
1. Click on Start, move the cursor to Settings, and then click on Control Panel.
2. Double-click on System.

The following window appears:

You can check the version in this window. Read the numbers under System.
4.00.950a means that it is Windows 95 OSR1.
4.00.950B means that it is Windows 95 OSR2.1.

Overall Procedure
1. Have the Windows 95 installation package in hand.
2. Back up your software and personal data files on the hard disk.
3. Create the installation diskettes of the device drivers using the Diskette Factory program. You need to create at least the following device driver diskettes:

Device Driver	Diskette Name
ThinkPad Configuration program	Utility Features for Windows 95
	Utility Features for DOS
Display driver	Video Features Package (NM2160) for Windows 95
PC Card support software	Available from Diskette Factory or Customization CD
Audio device driver	Audio Features Features for Windows 95
TrackPoint driver	TrackPoint Driver Features II for Window 95

Note: If you have already formatted the hard drive, you can download these drivers by clicking on the links in the table above.

Note: The ThinkPad Configuration program is not supported by the Windows 95 OSR0

Note: The ThinkPad Configuration program and PC Card support software (CardWizard) are not supported by Windows 95 OSR1.

4. Install Windows 95 and the software.

Note: To use the CD-ROM drive to install Windows 95, create the DOS boot diskette that enables to use the CD-ROM drive then boot the system with the diskette.

Installing Microsoft Windows 95
Some new files must be incorporated at the time of installation.

Installing Windows 95 OSR1
1. Create a Windows 95 supplementary diskette using the Diskette Factory program (refer to the User's Reference).
2. Make sure there is enough space in the hard disk to store the cabinet files and the installation programs (the required space might vary depending on the national language supported by your version of Windows 95).
3. Make a temporary directory.
For example, enter at the DOS prompt: MD c:\win95

4. Insert the Windows 95 CD-ROM into the CD-ROM drive.
5. Copy all the cabinet (.CAB) files and the installation programs from the \WIN95 directory of the Windows 95 CD-ROM to the temporary directory. For example, enter at the DOS prompt:
COPY src_cd:\WIN95\ . . c:\win95
where src_cd is the drive letter of the CD-ROM drive (D, E, F...), c is the drive letter of your hard disk drive, and win95 is the temporary directory that you made in step 3.

6. Insert the Windows 95 supplementary diskette you created in step 1 into the diskette drive.
7. Copy the updated files from the Windows 95 supplementary diskette to the temporary directory. For example, enter at the DOS prompt:
COPY A:\OSR INF\ . c:\win95
where c is the drive letter, and win95 is the temporary directory that you made in step 3.

8. Install the operating system by entering SETUP.EXE at the temporary directory prompt.
9. Refer to the Windows 95 documentation and the instructions that appear on the screen to complete the installation.
10. If required, install the Service Pack Version 1, available from the Microsoft Internet home page.
11. Remove all the files in the temporary directory and then remove the directory itself after you complete the installation, to free the space on the hard disk.

Installing Windows 95 OSR2.1
If you have a CD-ROM version of the Windows 95 OSR2.1, do the following:
1. Create a Windows 95 supplementary diskette using the Diskette Factory program (refer to the User's Reference).
2. Make sure there is enough space in the hard disk to store the cabinet files and the installation programs (the required space might vary depending on the language supported by your version of Windows 95).
3. Make a temporary directory. For example, enter at the DOS prompt: MD c:\win95

4. Insert the Windows 95 CD-ROM into the CD-ROM drive.
5. Copy all the cabinet (.CAB) files and the installation programs from the \WIN95 directory of the Windows 95 CD-ROM disk to the temporary directory. For example, enter at the DOS prompt:
COPY src_cd:\WIN95\ . c:\win95
where src_cd is the drive letter of the CD-ROM drive (D, E, F...), c is the drive letter of your hard disk drive, and win95 is the temporary directory that you made in step 3.

6. Insert the Windows 95 supplementary diskette you created in step 1 into the diskette drive.
7. Copy the updated files in the Windows 95 supplementary diskette to the temporary directory. For example, enter the following at the DOS prompt:
COPY A:\OSR2INF\ . . c:\win95
COPY A:\CARDBUS\ . c:\win95
where c is the drive letter, and win95 is the temporary directory that you made in step 3.

8. Install the operating system by entering SETUP.EXE at the temporary directory prompt.
9. Refer to the Windows 95 documentation and the instructions that appear on the screen to complete the installation.
10. Change the current drive letter to the CD-ROM drive letter, and run \USBSUPP.EXE in the \OTHERS directory of the CD-ROM.
11. Change the drive letter at the DOS prompt to A, and run \QFE444\PCCARDUP.EXE
12. Reboot the system.
13. To replace the Unimodem drivers to support the Intel Video Phone application, from the DOS prompt, go to C:\WINDOWS\SYSTEM (or the SYSTEM subdirectory where Windows 95 is installed).
14. Rename the UNIMODEM.VXD and UNIMDM.TSP files by entering:
REN UNIMODEM.VXD UNIMODEM.BAK
REN UNIMDM.TSP UNIMDM.BAK

15. Copy the new files by entering COPY A:\UNIMODEM\ .
16. Refer to the documentation shipped with this version to finish the installation.

Installing the ThinkPad Configuration Program for Windows 95
Note: If this package is used for Windows 95, Internet Explorer version 4 or later will need to be installed.

To install the ThinkPad Configuration program for Windows 95:

1. Start Windows 95.
2. Extract the drivers onto the hard disk.
3. Click on Start -> Run...
4. Type in "x:\<path name>\SETUP.EXE". Then click on OK. where x: is the drive letter and <path name> is the path you extracted the files to. Default path is C:\DRIVERS\W98\UTILITY\
5. Follow the instructions on the screen.

Installing the Display Driver for Windows 95
To install the display driver for Windows 95:
Windows 95 (Retail Version, Service Pack 1)

1. Boot Windows 95.
2. Extract the drivers onto the hard disk.
3. Click on the Start button.
4. Move the cursor to the Settings then click on the Control Panel.
5. Double-click on the Display icon.
6. Select the Settings tab.
7. Click on the Change Display Type... button.
8. Click on the Change... button under 'Adapter type' field.
9. Click on the Have Disk... button.
10. Type C:\DRIVERS\W9X\VIDEO and click on the OK button.
11. Windows 95 finds 'NeoMagic MagicGraph 128XD' then click on the OK button. Windows 95 copies all driver files to your hard disk.
12. After driver files are copied, click on the Close button to close the 'Change Display Type' window.
13. Select color depth, resolution, and font.
14. Click on the Close button to close the 'Display Properties' windows.
15. Click on the Yes button to restart Windows 95.

Windows 95 (OSR2: OEM Service Release 2)

1. Boot Windows 95.
2. Extract the drivers onto the hard disk.
3. Click on the Start button.
4. Move the cursor to the Settings then click on the Control Panel.
5. Double-click on the Display icon.
6. Select the Settings tab.
7. Click on the Advanced Properities button.
8. Click on the Change... button in the 'Adapter' tab.
9. Click on the Have Disk... button.
10. Type C:\DRIVERS\W9X\VIDEO and click on the OK button.
11. Windows 95 finds 'NeoMagic MagicGraph 128XD' then click on the OK button. Windows 95 copies all driver files to your hard disk.
12. After driver files are copied, click on the Close button to close the 'Advanced Display Properities' window.
13. Select color depth, resolution, and font.
14. Click on the Close button to close the 'Display Properties' windows.
15. Click on the Yes button to restart Windows 95.

Installing PC Card Support Software for Windows 95
Notes:
Windows 95 OSR1 does not support the PC Card support software. If you are going to use a enhanced port replicator with your computer, you need to uninstall CardWizard first, dock your computer to the enhanced port replicator, and then reinstall it. Remove any PC Cards from the computer.
1. Push the PC Card eject button; the eject button pops out.
2. Push the button again; the PC Card pops out.

To install the PC Card support software for Windows 95:
1. Start Windows 95.
2. Remove any PC Cards from the computer.

Note: Push the PC Card eject button; the eject button pops out. Push the button again; the PC Card pops out.

3. Insert the CardWorks for Windows 95 Diskette into the diskette drive.
4. Click on Start.
5. Click on Run...
6. Make sure the window shows A:\SETUP; then click on OK. Follow the instructions on the screen.

Installing the Audio Device Driver for Windows 95
To install the audio support software for Windows 95:

1. Start Windows 98.
2. Extract the drivers onto the hard disk.
3. Click on Start.
4. Click on Run.....
5. Type C:\DRIVERS\W9X\AUDIO\SETUP and click on OK.
6. Click on the "Uninstall Crystal Drivers" button at the pop-up window. (Do not click the "Install Driver" button.)
7. Follow the instructions on the screen.
8. When you are prompted to restart the computer, remove any diskette from the diskette drive and restart the computer.
9. When the computer prompts you to install the manufacturer's diskette during the startup of Windows 98, type C:\DRIVERS\W9X\AUDIO.
10. Follow the instructions on the screen to complete the installation.

Note: The MIDI connector is available if the computer is attached to the enhanced port replicator (option). The MIDI connector capability is disabled as a default, so you need to enable the function with the ThinkPad Configuration program.

Installing the IBM TrackPoint Driver for Windows 95
The TrackPoint Driver Diskette II for Windows 95/98/NT is intended for use with the IBM PS/2 TrackPoint Version 4.0 or later.

To install the TrackPoint driver for Windows 95:

1. Start Windows 95.
2. Extract the drivers onto the hard disk.
3. Click on Start.
4. Move the cursor to Settings; then click on Control Panel.
5. Double-click on the Mouse icon.
6. Click on the General tab.
7. Click on Change.
8. Click on Have Disk.
9. Type C:\DRIVERS\WIN\TPOINT and click on OK.
10. Select PS/2 TrackPoint in the list.
11. Click on OK.
12. Click on Close in the "Mouse Properties" window.
13. Restart your computer to make the new settings effective.

	Search Keywords
	Hint Category	Software Installation/Configuration, Windows 95
	Date Created	24-08-98
	Last Updated	17-05-99
	Revision Date	26-05-2000
	Brand	IBM ThinkPad
	Product Family	ThinkPad 560Z
	Machine Type	2640, 2641
	Model	All
	TypeModel
	Retain Tip (if applicable)
	Reverse Doclinks and Admin Purposes