13.950 bytes

Service Hints & Tips

Document ID: GJAN-3RNKCE

Achiever PC 3000 - Re-installing the original software for systems with Mwave

Applicable to: Canada

Question:
How do I reload my PC3000 with the Mwave adapter?

Answer:
Follow the steps below.

*** ATTENTION ***
If you follow the steps below, you will lose all your data and program files. The hard drive will no longer contain any personal information. If you have important files you wish to keep, please save them before going any further.

For this operation you will need:
The Windows 95 start-up disk
The Windows 95 CD
The 6 multimedia modem installations disks
Certificate of Authenticity (found on the cover of the Windows 95 manual)

Re-installing Windows 95

  1. Insert the Windows 95 start-up disk and then start the computer.
  3. When at the A:\ prompt insert the Windows 95 CD.
  5. Type the word "FDISK" and press Enter.
  7. Choose option 3 and press Enter.
  9. Choose option 1, then press Enter.
  11. When you see the warning just press the Enter key.
  13. It will then ask you for the volume label, it should be written under where it says VOLUME LABEL.
  15. Enter the volume label and then press Enter.
  17. When it asks you if you are sure, press Y and then press Enter.
  19. Press the Escape key to continue.
  21. Choose option 1 and press Enter.
  23. From the second menu choose option 1 and then press Enter.
  25. When it asks you if you wish to use the maximum available space answer YES and press Enter.
  27. Restart the computer.
  29. At the A:\ prompt type "FORMAT C:" and press Enter.
  31. When asked for a volume label just press Enter.
  33. Then at the A:\ prompt type "D:" and press Enter.
  35. At the D:\ prompt type "SETUP" and press Enter.
  37. Then press the Enter key to continue.
  39. At this point the mouse will work, you can then click on Continue.
  41. Click on YES to accept the software agreement.
  43. Click on NEXT to start collecting information about the hardware installed in your computer.
  45. Click on NEXT to install Windows 95 into the default directory.
  47. Click on NEXT for a typical installation.
  49. Enter the Certificate of Authenticity number found on the cover page of your Windows 95 guide.
  51. Then click on NEXT.
  53. Enter your Name and Company (company optional), then click on NEXT.
  55. Click on NEXT, Windows will then analyze your computer for the installed options.
  57. Click NEXT to install the most common components.
  59. Click on NO I DO NOT WANT A START-UP DISK, then click on NEXT.
  61. Click on NEXT to start copying the files to your hard drive.
  63. Remove the start-up disk from the A:\ drive.
  65. Click on FINISH to restart the computer.
  67. Click on OK when prompted to insert the Windows 95 CD.
  69. Click on CANCEL to continue.
  71. Click on the down arrow in the date and time properties to select the appropriate time zone.
  73. Click on CLOSE , then click on NEXT.
  75. Click on CANCEL in the ADD PRINTER WIZARD. You will install your printer with the specific disks it came with.
  77. Click on OK to restart the computer.

Re-installing the sound

  1. Insert the Diskette labeled, Multimedia Modem Windows disk 1 into the floppy drive.
  3. Click on Start, Settings, Control Panel.
  5. Select ADD/Remove Programs.
  7. Select INSTALL.
  9. Click on NEXT.
  11. Click on FINISH.
  13. At the installation window run the Complete Installation.
  15. When asked for the various disks, insert them accordingly.
  17. When prompted to restart the computer, do NOT do so, simply exit the installation and then click on Start, shutdown, restart the computer in MS-DOS mode, then click on YES. Remove the disk from the floppy drive.
  19. At the C:\WINDOWS> prompt, type "CD \" and press Enter.
  21. Then type "CD DSP2\SOLO" and press Enter.
  23. Then type "CONFIG" and press Enter.
  25. The first message you will see is just to ensure that the board is installed. Press Enter to accept it.
  27. Use the down arrow to highlight Setup and press Enter.
  29. Make sure the following values are displayed

  2. DSP BASE I/O.................0XCE30
    DSP DMA..........................7
    DSP IRQ............................10
    SB BASE I/O.....................0X220
    SB DMA..............................1
    SB IRQ................................7
    MIDI IRQ.............................9
    MIDI BASE I/O..................0X330
    COM PORT.......................3
    COM IRQ............................5
    CD-ROM IRQ...................NONE
    CD-ROM BASE I/O........0X0 (OR DISABLED)
    JOYSTICK........................ENABLED


    1. If anything else is displayed, use the down arrow key to select the item you need to change, press enter to open the list of choices, select the correct setting and press enter to change the value.
    3. When done, use the down arrow key to highlight OK and press Enter to accept.
    5. Move down and highlight TEST and press Enter, it should then run 6 tests and pass them all.
    7. When the testing stops, press Enter again.
    9. Then with the down arrow move to highlight EXIT and press Enter.
    11. Press Enter to update the CONFIG.SYS and other files.
    13. Then press Enter again to exit the program.
    15. Once back at the C:\DSP2\SOLO prompt, restart the computer.
    17. You will now have sound.
    20. For the modem
    23. Once back in windows click on Start, Programs and Multimedia modem.
    25. Then click on MWAVE MODEM.
    27. At this point you will have a window with 2 lights in green, the 2 lights in green should be MR and HS.
    29. Leave it on the screen.
    31. Then click on Start, Settings and Control panel.
    33. Double click on the Add New Hardware icon.
    35. Then click on Next at the first window, Next at the second window and Next at the third window.
    37. Let the autodetection find the hardware. When it finishes there will be a Details button.
    39. Click on the Details button and the hardware installed should be a communication port.
    41. Then click on Finish.
    43. You will now be back at the Control panel.
    45. Double click on the Add New Hardware icon again.
    47. Click on Next at the first window, Next at the second window and Next at the third window.
    49. When done you should get the Details button again, if you click on it you should see 28.8 Mwave Data Fax.
    51. Click on Finish and then click on Next.
    53. The modem is now installed.
    55. Close the Control Panel.

    For the CD-ROM in DOS

    1. Click on Start, Run, and at the command line type in SYSEDIT, then click on OK.
    3. You will then see several files. The first one is the AUTOEXEC.BAT file, which you must add in the following line

    2. DEVICE=C:\WINDOWS\COMMAND\MSCDEX /D:MSCD001 /M:12 /L:D


      1. Once the line is added, close that window.
      3. When Windows asks if you want to save the changes answer YES.
      5. You will then see the CONFIG.SYS file. Add in the following:

      7. C:\DEV\OAKV111.SYS /D:MSCD001 /N:1


        1. Once the line is added in close the CONFIG.SYS file.
        3. Again it will ask you if you want to save the changes, answer YES.
        5. When done close all the other files until you get back the Windows desktop.
        7. Click on Start, Programs and MS-DOS prompt.
        9. At the C:\WINDOWS> prompt, type "CD \" then press Enter.
        11. You will them be at the C:\ prompt. Type in "MD DEV" then press Enter.
        13. Insert the Windows 95 start-up disk.
        15. Type in "A:" and press Enter.
        17. Type "CD AMBRA" and press Enter.
        19. Type "COPY *.* C:\DEV" and press Enter.
        21. Type "EXIT" and press Enter.
        23. Remove the start-up disk.
        25. Click on Start, Shutdown, and Restart the Computer followed by Yes, and the operation is complete.


        Search Keywords

        Hint Category

        Audio, CD-ROM Drives, Modems, Preloaded Software, Software Installation/Configuration, Windows 95

        Date Created

        13-02-98

        Last Updated

        03-03-99

        Revision Date

        14-05-2000

        Brand

        Ambra, IBM PC

        Product Family

        Achiever PC 3000, PC 350

        Machine Type

        6583, 6586

        Model

        V70; V80; 351; 451; 551; 552; 00B; 553

        TypeModel

        Retain Tip (if applicable)

        Reverse Doclinks
        and Admin Purposes