9.931 bytes |
Service Hints & Tips |
Document ID: MCGN-3VSKGV |
This document is provided to IBM and our Business Partners to help sell and/or service IBM products. It is not to be distributed beyond that audience or used for any other purpose. |
Netfinity7000 - ECA014: Netfinity 7000 power cord / receptacle compatibility
Applicable to: World-Wide
PURPOSE:
This ECA provides for the removal of a 220 Volt/16 Amp AC Power Assembly, 220 Volt/16 Amp Line Cord, and the installation of a 220 Volt/10 Amp AC Power Assembly and country specific 220 Volt/10 Amp Line Cord on the IBM Netfinity 7000 type 8651 model TH0/TM0 to allow for supplying AC power to the server using the more common 220 Volt/10 Amp wall receptacle specific to some countries.
One (1) 220 Volt/10 Amp AC Power Assembly, one (1) 220 Volt/10 Amp Line Cord, and Instruction Sheet are contained in the following FBM Kits respective to the countries that this ECA applies to:
Country |
FBM Kit |
China |
03K9151 |
Australia / New Zealand / Papua New Guinea / Argentina |
03K9152 |
Italy / Chile / Ethiopia / Libya / Somalia |
03K9153 |
Denmark |
03K9154 |
Switzerland / Liechtenstein |
03K9155 |
FEATURES:
Type, |
With |
Machines Affected |
B/M to be |
Service |
System |
8651 |
B/M0000000 |
NETFINITY 7000 TYPE |
B/M0000000 |
00.7 |
00.5 |
PHYSICAL CHECK:
- This ECA applies to servers located in or will be located in one of the following countries only:
China / Australia / New Zealand / Argentina / Papua New Guinea/ Italy / Chile / Ethiopia / Libya / Somalia / Denmark / Switzerland / Liechtenstein
- The customer requires that the Server is powered with a standard 220 Volt/10 amp Line Cord typical to the country.
- The Server has the Ship-level 220 Volt/16 Amp Power Assembly (the 220 Volt/16 Amp Power Assembly has a 220 Volt/16 Amp AC power connector located at the back).
- The Server is NOT in a IBM Server Rack.
PREREQUISITES: NONE
COMPANION: NONE
CONCURRENT: NONE
DETAIL:
This ECA replaces the Server's 220 Volt/16 Amp Power Assembly (FRU p/n12J3264) with a 220 Volt/10 Amp AC Power Assembly (FRU p/n03K8966) to allow use of the more common 220 Volt/10 Amp Power Cord specific to the counties specified in this ECA that may only have a 220 Volt/10 Amp wall receptacle.
1- Have the Local Administrator Down the Network Operating system.
2- Power down the Server.
Note: Refer to the Instruction Sheet that was packed in the FBM Kit or, Refer to the Hardware Maintenance Manual for the Netfinity 7000; the "AC Power Assembly" section describes the following steps in detail:
3- Remove the Hot-Swap Power Supplies.
4- Remove the 5-Volt Regulator Card.
5- Remove the 16 Amp AC Power Assembly.
6- Install the 10 Amp AC Power Assembly.
7- Install the 5-Volt Regulator Card.
8- Install the Hot-Swap Power Supplies.
9- Power on the Server, check the Server's Power Supply Status Indicators to be sure that all the Hot-Swap Power supplies are operating correctly (refer to the Hardware Maintenance Manual for the Netfinity 7000, see the "Status Indicators" section).
NOTES:
THIS ECA IS "AS REQUIRED".
ONLY IBM AUTHORIZED SERVICERS MAY APPLY THIS ECA.
THIS ECA WILL EXPIRE 10/13/2004.
*********************************************************************************************************************************************
FOR NORMAL SERVICE ACTIVITY IN THE COUNTRIES SPECIFIC TO THIS ECA USE THE FOLLOWING FRU P/N'S:
- 10 Amp Power Assembly (FRU p/n03K8966)
- 16 Amp Power Assembly (FRU p/n12J3264)
- Power Cords:
Country |
10 Amp |
16 Amp |
China |
02K0546 |
01K9851 |
Australia/New Zealand/Papua New Quinea/Argentina |
13F9940 |
12J5128 |
Italy/Chile/Ethiopia/Libya/Somalia |
14F0069 |
12J6126 |
Denmark |
13F9997 |
55H6646 |
Switzerland/Liechtenstein |
14F0051 |
55H6646 |
NOTE: 10 Amp Power Assembly requires 10 Amp Power Cord, 16 Amp Power Assembly requires 16 Amp Power Cord.
********************************************************************************************************************************************
WHEN IMPLEMENTING THIS ECA:
Country Specific FBM kits must be ordered using Code B and reference ECA014 (Any orders for the FBM kits under normal FBM replacement parts will be rejected).
Discard the 16 AMP Power Assembly and 16 Amp Cord.
USA:
This ECA does not apply to any servers in the USA or any other country in North America, due to the Electrical Standards used.
EMEA:
PSS:
CE's should record all time and parts to Service Code 33, (8651) ECA014, Other Office 990.
BUSINESS PARTNERS:
Refer to Warranty Claim System; Use Emergency Warranty Claim type 5 (ECA), quoting CPPS ECA Code: M/T 8651 = "SE"
SAS KEYWORDS:
PSY2, SERVICER ONLY, D/T8651, NETFINITY, 7000, 03K9151, 03K9152, 03K9153, 03K9154, 03K9155, 03K8966, 12J3264, 03K8966, PSY3ECA, ECA014, FBM, H164030
Search Keywords |
PSY2, SERVICER ONLY, D/T8651, NETFINITY, 7000, 03K9151, 03K9152, 03K9153, 03K9154, 03K9155, 03K8966, 12J3264, 03K8966, PSY2ECA, ECA014, FBM, H164030 | |
Hint Category |
ECA, Power, Retain | |
Date Created |
25-06-98 | |
Last Updated |
16-09-98 | |
Revision Date |
15-09-99 | |
Brand |
IBM PC Server | |
Product Family |
Netfinity 7000 | |
Machine Type |
8651 | |
Model |
TH0; TM0 | |
TypeModel |
| |
Retain Tip (if applicable) |
| |
Reverse Doclinks |
Date created: O98/01/27, Date last altered: A98/09/14, Owning B.U.: USA |