|
14.439 bytes |
Service Hints & Tips |
Document ID: RMIE-3J6EYN |
|
This document is provided to IBM and our Business Partners to help sell and/or service IBM products. It is not to be distributed beyond that audience or used for any other purpose. |
IBM PC140 - EMEA technical information
Applicable to: EMEA
Index:
|
1. Technical Information 2. Hardware Requirements |
3. Software Requirements 4. Limitations |
Technical Information
Hardfile Specifications
Formatted capacity* 635MB 850MB
Average seek time 12ms 14ms
Average latency 6.7ms 6.7ms
Sector interleave 1:1 1:1
Interface EIDE EIDE
Read/Write Cache Yes Yes
* MB equals million bytes. Mb equals million bits
Actual user-accessible capacity may vary slightly based on different operating environments.
Mechanical Specifications
1. 6260 Dimensions/Weights
Width - 440mm (17.32 inches)
Depth - 420mm (16.53 inches)
Height- 102mm ( 4.00 inches)
Weight- 8.0kg (17.61 pounds) ship configuration
Weight- 10.0kg (22.0 pounds) maximum configuration
Electrical Power Specifications
6260 models - 145 watt supply with fixed speed fan
- 110 volt or 220 volt operation controlled by a
switch on the back of the unit
- Built in overload protection
100-125 (nominal) V ac; 50-60 Hz; 3 Amp (max)
200-240 (nominal) V ac; 50-60 Hz; 1.5 Amp (max)
Ambient Air Temperature Specifications
System on: 10.0 C - 35.0 C (50 F - 95 F)
at Altitude sea level 0 to 2134m or 0 to 7000 ft.
System off: 10.0 C - 43.0 C (50 F - 110 F)
at Altitude sea level 0 to 2134m or 0 to 7000 ft.
Relative Humidity: 8% - 80%
Advanced Power Management:
The IBM PC 100 Series Systems are designed to meet the EPA Energy Star (1) requirements for using less than 30 Watts of power in idle mode when enabled by the Power Management software provided with the systems. All of the systems released in this announcement meet this requirement of less than 30 watts of power consumption in idle mode when the Power Management function is fully enabled.
Power consumption is dependent upon many variables including system memory, L2 cache, video memory, number and type of hard files, and adapter cards installed. All of the IBM PC 100 Series Systems have processors and hardfiles that support Power Management.
(1)The Energy Star emblem does not represent EPA endorsement of any product or service. EPA, as a matter of policy, does not endorse any particular company and it's products.
Noise Level Specifications:
Declared Acoustical Noise Emissions (idle mode): LWAd = 4.8 Bels
Note:
The noise emission level stated is the declared (upper limit) A-weighted sound power level, in bels, for a random sample of machines, typically configured and operating in idle mode; i.e., powered on, but no DASD read/write or other I/O activity. All measurements have been made in accordance with ANSI S12.10, and reported in conformance with ISO 9296.
Equipment Approvals
CISPR22 - Class B
When configured with cabling that meets IBM Specifications
GOP
TUV-GS - EN60950 (business - means of proving compliance to
EEC safety directives)
TUV-GS - ZH1/618 (business - German ergonomics requirements)
NEMKO - EN60950 (Norway - legal requirement)
SEMKO - EN60950 (Sweden - legal requirement)
DEMKO - EN60950 (Denmark - legal requirement for registration
only, business for D mark)
EIF (SETI) - EN60950 (Finland - legal requirement, circle FI)
OVE - EN60950 (Austria - IBM Austria business requirement,
not a legal requirement)
CE (Europe - legal requirement, emissions and
safety compliance)
BABT - UK General Approval
NS/G/1234/J/100003(Telecommunications Safety only, no approval mark)
IECEE CB Certificate (World Wide - IEC 950/EN60950)
ISO Compliance:
All systems are ISO 9241-3 capable when used with an ISO capable monitor and appropriate software with ISO-compliant fonts.
Operating Environment
6260 Operating Environment
System on: 10 C to 35 C ( 50 F to 95 F)
at Altitude sea level 0 to 2134 m or 0 to 7,000 ft.
System off: -40 C - 70 C (-40 F - 158 F)
at Altitude sea level 0 to 2134 m or 0 to 7,000 ft.
Relative Humidity: 8% to 80%
Wet Bulb: (Calorific value) : 493 BTU (max.)
Electrical power: 90 - 137V ac, .08 KVA max.
:180 - 265V ac, .30 KVA max.
Capacity of Exhaust : .42 Cubic meter/min. 15 CFM
Noise Level: 4.8 Bels
Leakage and starting current: 3.5mA
Hardware Requirements
Monitors
Monitors supported by the IBM PC 140 systems are:
1. IBM 2238 Color Monitors
2. IBM 2248 Color Monitors
3. IBM P70 (6554-6xx) Color Monitors (Energy Star and NUTEK Capable)
4. IBM P200 (6555-7xx) Color Monitors (Energy Star and NUTEK Capable)
5. IBM G40 (6542-1xx) Color Monitors (Energy Star Capable)
6. IBM G41 (6542-3xx) Color Monitors (Energy Star and NUTEK Capable)
7. IBM G50 (6543-3xx) Color Monitors (Energy Star and NUTEK Capable)
8. IBM G70 (6544-4xx) Color Monitors (Energy Star and NUTEK Capable)
Video:
All IBM PC 140 systems have a PCI Local Bus providing SVGA graphics. Operating system/driver support is required to provide the following VGA and SVGA video modes. All systems have 1MB of video memory (DRAM) standard and support the following video modes.
1. 640x480, 256 colors (60,72,75,85Hz)ñ 640x480, 32K colors (60,72,75,85Hz) 14
2. 640x480, 64K colors (60,72,75,85Hz)
3. 800x600, 16 colors (60,72,75Hz)
4. 800x600, 256 colors (60,72,75,85Hz)
5. 800x600, 32K colors (60,72,75,85Hz)
6. 800x600, 64K colors (60,72,75,85Hz)
7. 1024x768, 16 colors (43(I),60,70,75Hz)
8. 1024x768, 256 colors (43(I),60,70,75,85Hz)
9. 1280x1024, 16 colors (43(I),60,72,75Hz)
10. 1280x1024, 256 colors (43(I),60,72,75Hz)
With an additional 1MB of video DRAM (optional), the following modes are supported:
1. 640x480, 16M colors (60,72,75,85Hz)
2. 800x600, 16M colors (60,72,75Hz)
3. 1024x768, 32K colors (43(I),60,70,75Hz)
4. 1024x768, 64K colors (43(I),60,70,75Hz)
5. 1280x1024, 256 colors (43(I),60,72,75Hz)
Notes:
1. All modes are non-interlaced unless otherwise noted. (I) indicates interlaced.
2. The monitor attached should support the modes and frequencies desired.
3. MFI modes 2, 3 and 4; MFI mode 5 (132 columns) is supported in some graphics modes. Note: The monitor attached should support the modes and frequencies desired.
Software Requirements
Operating System Software:
The primary operating system environments for IBM PC 140 will be IBM PC DOS Version 7.0 and Microsoft Windows 3.1. and/or Windows 95. The operating systems will be pre-installed on selected models. Systems that are pre-installed will not ship with operating system diskettes, but will be pre-installed with Diskette Factory, a utility that allows customers to produce the diskette images of the pre-installed software.
IBM PC 140 will be tested for compatability with the following operating systems.
PC DOS 7.0
MS-DOS (**) 6.2
OS/2 (*) 2.11 (VGA only)(1)
OS/2 (*) 3.0 Warp (*)
MS Windows (**) 3.1
MS Windows For Work Groups (**) 3.11
MS Windows 95 (**)
MS Windows NT (**) 3.51 (Client)
OS/2 (*)LAN Server 4.0
Novell Netware (***)3.12
Novell Netware (***)4.01
SCO Unix 3.2v4.2
SCO OpenServer (***)5.0
SCO Open Desktop(***)3.0
AIX (***) 1.3
(*) Trademark of International Business Machine Corporation
(**) Trade Mark of Microsoft Corporation
(***)Any product names appearing in this publication may be trademarks of their respective owners.
(1) Additional drivers are also needed for IDE CDROM and SVGA and are available on the OS/2 bulletin board. 15
Note:
Operating System video graphics driver support is required for IBM PC 140 SVGA graphics capabilities. Although these systems will be compatibility tested with the above operating systems, additional video driver support may be required from the operating system vendor.
Diskette Factory:
The Diskette Factory Icon allows the user to build (copy from hardfile to diskette) diskette copies of the original system software products that came pre-installed on the hard file. These pre-installed software products include PC DOS, Windows, SVGA video drivers, diagnostics, and other program diskettes.
BIOS:
FLASH ROM supports Compatibility BIOS (CBIOS) and POST.
(TM) Trade Mark of IBM Corporation.
Plug and Play Support:
All systems support the Plug and Play specifications designed to make it easier for users to install, upgrade, and make changes to their Personal Computers. Plug and Play systems utilizing Plug and Play adapter cards are self-configuring.
All systems have BIOS support and a Plug and Play Utility that supports this emerging technology for hardware and software.
Advanced Power Management (APM):
The IBM PC 100 Series Systems systems have an APM feature called standby. This power management feature places the system in standby mode after a user-defined time interval elapses with no activity. The system resumes operation when the keyboard or mouse is used. Systems with preinstalled software come with this power management feature already set up. The setup utility program has a default setting of 20 minutes for automatically initiating power management of the display, processor, and hard disk.
The scheduler feature is used to start events, such as resume or program initiation, when the system is in the standby mode.
Compatibility
The IBM PC 140 is compatible with the IBM Personal Computer, Personal Computer XT (TM) and Personal Computer AT (R) at the BIOS interface level (BIOS not identical) and at most hardware interfaces. The IBM PC 140 has been designed to maintain compatibility with existing personal computer software and non-timing dependent features.
Limitations
1. Of the 128MB of maximum system memory, the system requires 348K for its use. This leaves the customerswith a maximum of 127.6MB of the memory address space for their usage.
2. 72-pin (70ns) Industry Standard Memory SIMMs, 128MB maximum memory
3. Maximum External (L2) cache memory supported is 256Kb asynchronous (optional)
4. Standard Video RAM is 1MB, with an optional 1MB upgrade supported
5. System supports horizontal orientation only, vertical orientation and the use of a floor stand is not supported
6. Maximum number of four (4) IDE devices supported
7. Maximum number of 2 diskette drives supported
8. Memory can only be added in matched pairs
9. If all I/O card slots are populated, average wattage of the I/O cards should be limited to 8.5 Watts. Populating all I/O card slots with options that have an average load of greater than 8.5 Watts will cause recommended thermal limits in the I/O card area to be exceeded
|
Search Keywords |
| |
|
Hint Category |
General Information | |
|
Date Created |
27-05-96 | |
|
Last Updated |
16-04-98 | |
|
Revision Date |
15-04-99 | |
|
Brand |
IBM PC | |
|
Product Family |
PC 140 | |
|
Machine Type |
6260 | |
|
Model |
Various | |
|
TypeModel |
| |
|
Retain Tip (if applicable) |
| |
|
Reverse Doclinks |