|
Symptom / Error |
FRU / Action in Sequence |
|
10X
101 Interrupt failure
102 Timer failure
103 Timer interrupt failure
104 Protected mode failure
105 Last 8042 command not
accepted
107 NMI test failure
108 Timer bus test failure
109 Low meg-chip select test |
1. System board |
|
110
(Planar parity) |
1. Go to "Memory Checkout" on page 12 of the HMM
2. DIMM card
3. Detach the expansion unit if it is attached to the computer
4. System board |
|
111
(I/O parity) |
1. Go to "Memory Checkout" on page 12 of the HMM
2. Port replicator
3. System board
|
|
127
(Cache error) |
1. CPU mini-cartridge
2. System board |
|
158
(Hard disk password was not set even though the supervisor password is set) |
1. Set the password for hard disk drive |
|
159
(Hard disk password is not set the same as the supervisor password) |
1. Set the correct password for hard disk drive |
|
161
(Dead battery) |
1. Go to "Checking the Backup Battery" on page 16 of the HMM
2. Backup battery
3. System board |
|
163
(Time and date were not set) |
1. Set time and date
2. System board |
|
173
(Configuration data was lost) |
1. Select OK in the error screen; then set the time and date
2. Backup battery
3. System board |
|
174
(Configuration error: Perform "Checking the Installed Devices List" on page 35 of the HMM before changing any FRUs) |
1. Check device configuration
2. Hard disk drive assembly
3. System board |
|
175, 177, 178
175 EEPROM CRC #1 error
177 Supervisor password check
sum error
178 EEPROM is not functional |
1. System board |
|
183
(Incorrect password entered at the supervisor password prompt) |
1. Have the user examine the password |
|
184
(Power-on password check sum error) |
1. Reset the power-on password in Easy-Setup |
|
185
(The start-up sequence is not valid. Suspect that power was off when the start-up sequence was being updated) |
1. Reset the start-up sequence in Easy-Setup |
|
186 |
1. System Board. |
|
188
(EEPROM CRC #2 error) |
1. System board. |
|
190
(A depleted battery pack was installed when the power was on) |
1. Go to "Checking the Battery Pack" on page 16 of the HMM |
|
191XX
(PM initialization error) |
1. System board |
|
192
(A fan error) |
1. Fan
2. System board |
|
195
(The configuration read from the hibernation area does not match the actual
configuration) |
1. Check if the configuration was changed. For example, check if a DIMM card was added |
|
196
(A read error occurred in the hibernation area of the hard disk drive) |
1. Run the hard disk drive test
2. Reseat the HDD flat cable
3. Hard disk drive |
|
199XX
(Resume error) |
1. System board |
|
1XX |
1. System board. |
|
225
(An unsupported memory module) |
1. Check if a supported DIMM card is installed
2. DIMM card
3. System board |
|
2XX
201 Memory data error
202 Memory line error 00-15
203 Memory line error 16-23
205 Memory test failure on
on-board memory
221 ROM to RAM remap error |
1. Go to "Memory Checkout" on page 12 of the HMM
2. DIMM card
3. System board |
|
301, 303, 304, 305, 3XX
301 Keyboard error |
1. Go to "Keyboard or Auxiliary Input Device Checkout" on page 11 of the HMM
2. Keyboard
3. External numeric keypad
4. External keyboard
5. Keyboard/mouse cable
6. System board |
|
601, 6XX
601 Diskette drive or
controller error |
1. Go to "Diskette Drive Checkout" on page 11 of the HMM
2. Diskette drive assembly
3. Diskette
4. System board |
|
602
(Diskette read error) |
1. Go to "Diskette Drive Checkout" on page 11 of the HMM
2. Diskette
3. Diskette drive assembly |
|
604
(Unacceptable ID was read from the diskette drive) |
1. Go to "Diskette Drive Checkout" on page 11 of the HMM
2. Diskette drive assembly
3. System board |
|
11XX
1101 Serial_A test failure |
1. Serial device
2. Communication cable
3. System board |
|
12XX
1201 Serial_B test failure |
1. System board (infrared) |
|
17XX
1701 Hard disk controller
failure
1780, 1790 Hard disk 0 error
1781, 1791 Hard disk 1 error |
1. HDD flat cable
2. Hard disk drive
3. System board |
|
1801
(An unsupported port replicator) |
1. Make sure that the correct port replicator is connected. See page 79 of the HMM |
|
24XX
2401 System board video error |
1. System board. |
|
808X
8081 PCMCIA presence test
failure. (PCMCIA
revision number also
checked)
8082 PCMCIA register test
failure |
1. PC Card slot assembly
2. PCMCIA device
3. System board |
|
860X
(Pointing device error when TrackPoint is disabled)
8601 System bus error - 8042
mouse interface
8602 External mouse error
8603 System bus error or
mouse error |
1. External mouse
2. External keyboard
3. System board |
|
861X
(Pointing device error when TrackPoint is enabled)
8611 System bus error - I/F
between 8042 and IPDC
8612 TrackPoint error
8613 System board or
TrackPoint error |
1. Reseat the keyboard cable on the system board
2. Keyboard
3. External mouse
4. System board |
|
I9990301
I9990302
I9990305
I9990301 Hard disk error
I9990302 Invalid hard disk
boot record
I9990305 No bootable device |
1. Check that the operating system is installed in the hard disk drive. If not, install the operating system
2. Reseat the boot device
3. Reseat the HDD flat cable
4. Check the start-up sequence for the correct boot device
5. Check that the operating system has no failure and is installed correctly |
|
I9990303
(Bank - 2 flash ROM check sum error) |
1. System board |
|
Other codes not listed above |
1. Go to "Undetermined Problems" on page 31 of the HMM |
