TP 1400 - Numeric error codes index

5.117 bytes

Service Hints & Tips

Document ID: BMOE-423LW4

TP 1400 - Numeric error codes index

Applicable to: World-Wide

The following information is intended for IBM Dealers and Authorized Servicers only. Customers attempting to follow any of the procedures below may void their warranty.

Error
Code

Message

FRU/Action in Sequence

POST

010

Memory Error at MMMM:
SSSS:OOOOh (R:xxxxh, W:xxxxh)

1. Go to "Memory Check"
2. DIMM
3. Planar board

040

Diskette Drive Controller Error

1. Go to "Diskette Drive Check"
2. Ensure the diskette drive configuration setting in BIOS Utility is correct.
3. Diskette drive cable
4. Diskette drive
5. Planar board

047

Diskette Drive(s) Disabled

1. Ensure the diskette drive is not set to "Disabled" in the "System Security" menu of the BIOS Utility.
2. Diskette drive cable
3. Diskette drive

050

IDE Drive 0 Error

1. Ensure the hard disk drive is set to "Auto" in the "Basic System Settings" menu of the BIOS Utility.
2. Hard disk connection board
3. Hard disk drive
4. Planar board

054

IDE Drive(s) Disabled

1. Ensure the hard disk drive is not set to "None" in the "Basic System Settings" menu of the BIOS Utility.
2. Hard disk drive cable
3. Hard disk drive

056

IDE Drive 0 Auto Detection Failed

1. Ensure the hard disk drive is set to "Auto" in the "Basic System Set-tings"
menu of the BIOS Utility.
2. Hard disk connection board
3. Hard disk drive
4. Planar board

070

Real Time Clock Error

1. Reset time in the "Basic System Settings" menu of the BIOS Utility.
2. Backup battery (RTC battery)
3. Planar board

071

CMOS Battery Bad

1. Enter BIOS Utility and execute "Load Setup Default Settings".
2. Backup battery (RTC battery)
3. Planar board

072

CMOS Checksum
Error

1. Enter BIOS Utility and execute "Load Setup Default Settings"; then reboot the system.
2. Backup battery (RTC battery)
3. Planar board

006

Equipment Configuration Error

1. Ensure the equipment (diskette drive, hard disk drive, keyboard, external mouse, etc.) is connected properly
and is correctly set in the BIOS Utility.
2. Hard disk connection board
3. Hard disk drive
4. Planar board

System Operation (Runtime)

103

Press <Esc> to turn off NMI or other key to
reboot

1. Enter BIOS Utility and execute "Load Setup Default Settings"; then reboot the system.
2. Remove the nonfactory-installed
adapter card and reboot the system.

Search Keywords

Hint Category

Hardware Maintenance Information

Date Created

09-11-98

Last Updated

19-11-98

Revision Date

19-11-99

Brand

IBM ThinkPad

Product Family

ThinkPad i Series 1400

Machine Type

2611

Model

TypeModel

Retain Tip (if applicable)

Reverse Doclinks
and Admin Purposes

Error Code	Message	FRU/Action in Sequence
POST
010	Memory Error at MMMM: SSSS:OOOOh (R:xxxxh, W:xxxxh)	1. Go to "Memory Check" 2. DIMM 3. Planar board
040	Diskette Drive Controller Error	1. Go to "Diskette Drive Check" 2. Ensure the diskette drive configuration setting in BIOS Utility is correct. 3. Diskette drive cable 4. Diskette drive 5. Planar board
047	Diskette Drive(s) Disabled	1. Ensure the diskette drive is not set to "Disabled" in the "System Security" menu of the BIOS Utility. 2. Diskette drive cable 3. Diskette drive
050	IDE Drive 0 Error	1. Ensure the hard disk drive is set to "Auto" in the "Basic System Settings" menu of the BIOS Utility. 2. Hard disk connection board 3. Hard disk drive 4. Planar board
054	IDE Drive(s) Disabled	1. Ensure the hard disk drive is not set to "None" in the "Basic System Settings" menu of the BIOS Utility. 2. Hard disk drive cable 3. Hard disk drive
056	IDE Drive 0 Auto Detection Failed	1. Ensure the hard disk drive is set to "Auto" in the "Basic System Set-tings" menu of the BIOS Utility. 2. Hard disk connection board 3. Hard disk drive 4. Planar board
070	Real Time Clock Error	1. Reset time in the "Basic System Settings" menu of the BIOS Utility. 2. Backup battery (RTC battery) 3. Planar board
071	CMOS Battery Bad	1. Enter BIOS Utility and execute "Load Setup Default Settings". 2. Backup battery (RTC battery) 3. Planar board
072	CMOS Checksum Error	1. Enter BIOS Utility and execute "Load Setup Default Settings"; then reboot the system. 2. Backup battery (RTC battery) 3. Planar board
006	Equipment Configuration Error	1. Ensure the equipment (diskette drive, hard disk drive, keyboard, external mouse, etc.) is connected properly and is correctly set in the BIOS Utility. 2. Hard disk connection board 3. Hard disk drive 4. Planar board
System Operation (Runtime)
103	Press <Esc> to turn off NMI or other key to reboot	1. Enter BIOS Utility and execute "Load Setup Default Settings"; then reboot the system. 2. Remove the nonfactory-installed adapter card and reboot the system.

	Search Keywords
	Hint Category	Hardware Maintenance Information
	Date Created	09-11-98
	Last Updated	19-11-98
	Revision Date	19-11-99
	Brand	IBM ThinkPad
	Product Family	ThinkPad i Series 1400
	Machine Type	2611
	Model
	TypeModel
	Retain Tip (if applicable)
	Reverse Doclinks and Admin Purposes