|
13.433 bytes |
Preloaded Software Information |
Document ID: MCGN-3XWJ9T |
PC Server 320 EISA Non RAID - Installing NetWare 3.12
Applicable to: World-Wide
Installation instructions for installing NetWare 3.12 on a PC Server 320 EISA Non RAID Server.
Supported systems:
8640-0D0, 0DV, 0X0, 0XT, 0Y0, 0YT, 0YV, 0Z0, 0ZV, 1D0, 1DS, 1YS, 2D0, 2Z0, 3D0, 3Z0, 4D1, 4D2, 4D3, 4D4, 4Y5, 4Y6, 4YF, 4YG, 4YV, 4Z1, 4Z2, 5D1, 5D2, 5Z1, 5Z2, ANW, EE0, EEV, IS2, NNT, NTN, RE0, RE1, RES, REV, SB1, SUN, Z11, Z12, Z13, Z14, Z15, Z16, Z17, Z18, Z19, Z1A, Z1B, Z1C, Z1D, Z1E, Z1F, Z1G, Z1H, Z1J, Z1K, Z1L, Z1M, Z1N, Z1P, Z1Q, Z1R, Z1S
Follow the NOS instructions provided in this document sequentially unless you are instructed differently. Windows and messages might differ from those in this document.
This document contains the following:
1.0) What you will need
2.0) Where to download device drivers/files
3.0) Quick installation instructions for Experts
4.0) Detailed Installation Instructions:
4.1) Setting up the Hardware
4.2) Setting up the BIOS
4.3) Configuring the Adaptec SCSI subsystem
4.4) Installing the NOS
1.0) What you will need:
76h4891.exe (310689 bytes, 11-26-96) PC Server 320 EISA BIOS flash update diskette version 16T3b
78h6488.exe (841705 bytes, 10-17-96) PC Server 320 EISA configuration diskette version 4.02
PCIFW1.EXE (343461 bytes, 02-01-96) PC Server 320 PCI F/W device drivers diskette for NetWare, etc.
PCIFW5.exe (1422055 bytes, 02-01-96) PC Server 320 PCI F/W device drivers diskette 2 of 4 for DOS
A copy of PC DOS 7 and a copy of Novell NetWare 3.12
2.0) Where to download device drivers/files
IBM BBS (U.S.): 1-919-517-0001
- IBM FTP site: ftp://ftp.infania.net/pccbbs/pc_servers/
- IBM U.S. web site: http://www.pc.ibm.com/us/searchfiles.html
- For IBM PC sites in other countries, begin at: http://www.pc.ibm.com
- Microsoft web site: http://www.microsoft.com/support/
- Microsoft FTP site: ftp://ftp.microsoft.com/bussys/winnt/winnt-public/fixes/
If you are very familiar with SCSI, hardware, and the installation process, continue with 3.0 Quick Installation Instructions for Experienced Users. If not, continue with 4.0 Detailed Installation Instructions.
3.0) Quick instructions
1) Ensure the Adaptec controller is set up properly and low level the drive. (Extended BIOS translation is to be disabled for NetWare 3.12.)
2) FDISK the drive. Ensure an active primary partition the size of your RAM + 50 Meg.
3) Install PC DOS 7 (optional components not required). When complete, run DOSINST from the PCIFW5.EXE Diskette (section 2) for CD ROM support.
4) Copy all files from the \NETWARE\V3_1X directory on disk PCIFW1.EXE to a directory on the DOS partition. Start the NetWare install from CD #1 by running Install from the appropriate language directory under \SERVER.312 directory on the CD ROM. Load AIC7870.DSK from the directory you created for the PCIFW1.EXE files and add the appropriate lines to STARTUP.NCF. Install and configure networking components as normal.
5) It is mandatory to apply all fixes and patches from http://support.novell.com for correct operation.
4.0) Detailed instructions.
Follow the instructions below in sequence:
4.1) Setting up Hardware
Note: Follow the on screen directions on the following disk operations:
Boot to the BIOS upgrade diskette (listed in section 2) and flash the system to revision 16T3B.
4.2) Running EISA config
1) Boot up to the EISA config disk. (Disk listed in section 2)
2) Type Y at Configure System now?.
3) Go to step 3, View or Edit Details.
4) Select Total System Memory.
5) Press Enter.
6) Select the correct memory size and press F10.
7) Press F10 again.
8) Go to Step 2, Add and Remove Boards.
9) Press Insert.
10) Press Enter.
11) Select ISA SVGA Video Card and press Enter.
12) Press Enter again.
13) Select Slot 1 and press Enter.
14) Select Step 5, Save and Exit.
4.3) Setting up the Adaptec SCSI Subsystem
Note: For open bay models or any SCSI chain setup issues, download Faxback document # 33050.
1) Boot the server and press CTRL A when prompted on the screen to enter 'SCSI Select'.
2) Select 'Configure/View Host Adapter Settings'.
3) Press F6 to restore defaults. Select yes to reset all options to default. Open SCSI device configuration, on the lines which say 'Send Start Unit Command' set all IDs for active hard disks to yes.
4) Press ESC to return to previous menu.
5) Select advanced configuration options.
6) Set 'extended BIOS translation for DOS drivers > 1 gbyte' to disabled. (Note that DOS will only see space within the first 1024 cylinders of the hard disk, however Novell will recognize the full volume.)
7) Press ESC twice. Say yes to save any changes which are made.
8) Select SCSI Disk Utilities (A SCSI bus scan should occur).
9) For each hard drive that appears in the list perform the following:
A) Highlight the drive.
B) Select "Format Disk". (Note: A status bar does not appear. Allow to run until complete.)
4.4) Installing the NOS
1) Boot your PC DOS 7 installation disk. Select Y when asked if you wish to install.
2) When PC DOS asks you to partition the drive, select 'Allocate some free hard disk space for PC DOS'.
3) FDISK now starts. Select #1, Create DOS partition or Logical DOS Drive. Select #1, Create Primary DOS Partition. When asked "Do you want to use the maximum available size..." enter N. For the partition size, enter the amount of your system RAM, plus 50 Meg and press Enter. Press ESC to return to the main FDISK screen.
4) Select #2, Set Active Partition. Enter the partition number of the partition you just created and press Enter. Press Esc twice to continue (system reboots, leave the DOS disk in the diskette drive).
5) Repeat step 1. When the screen prompts, select Format Partition. After completion, press Enter at the Welcome screen. Press Enter again after verifying the date, time, etc.
6) A list is presented of optional components. Ensure all options say NO and the path to the DOS install target is C:\DOS. Select Continue Setup. Follow onscreen directions until DOS asks you to remove all disks and press any key to restart.
7) After booting to the C: prompt, type the following:
DEL C:\CONFIG.SYS Press Enter.
DEL C:\AUTOEXEC.BAT Press Enter.
Place the PCIFW1.EXE disk in the drive. Type the following:
COPY A:\NETWARE\V31_X\*.* C:\SCSI\*.*
Press <ctrl><alt><del> to reboot.
8) Enter the date and time. Place PCIFW5.EXE in the diskette drive (see section 2). Type the following:
A:\DOSINST Press Enter.
For the EZ-SCSI program, accept defaults for every question it asks (usually by pressing Enter).
Press <ctrl><alt><del> to reboot.
9) After reboot, type the following at the c: prompt:
E CONFIG.SYS
Enter the following lines at the end of the CONFIG.SYS file:
FILES=40
BUFFERS=30
STACKS=9,256
LASTDRIVE=Z
Press F4 to save and exit. Press <ctrl><alt><del> to reboot.
10) After reboot, place the NetWare 3.12 CD in the CD ROM drive and switch to the drive letter of the CD ROM (it was echoed on boot when MSCDEX loaded). Change to the \NETWARE.312\English directory. Type INSTALL and press Enter.
11) Read the Ethernet Frame Type message and press Enter. Select to Install NetWare 3.12 from the menu. Select to Retain Current Disk Partitions.
12) Enter the desired ServerName. Accept the given internal network number. Accept default source and target paths. File copy now begins (insert the "SYSTEM_1" diskette as prompted). Accept all defaults until the copy operation completes and you are at a NetWare command prompt.
13) Type load c:\scsi\aic7870.dsk Write down the slot number presented, then press Enter to accept it. Type load install . Choose 'Disk Options', 'Partition Tables', 'Create NetWare Partition'. Accept the default size and other parameters to take the balance of freespace (press Esc). Select yes to create. Press Esc twice. Select Volume Options. Press Ins to create a new volume. Accept the default name of SYS along with the other parameters and press Esc. Select 'System Options', 'Copy System and Public Files'. Read the message about mounting the SYS volume and press Esc. Select yes to mount it. Press F6 when prompted to install from the CD.
14) Enter the path you ran 'Install' from in Step 10. File copy now begins. When complete, press Esc to continue. Select to 'Create AUTOEXEC.NCF File'. Accept the text and press Esc. Select yes to save. Select to 'Create STARTUP.NCF File'. Accept the default path. Change the AIC7870 line to read:
load c:\scsi\aic7870 slot=<insert the slot number recorded in step 13>
Press Ecs. Select yes to save. Select 'Return to Main Menu'. Select to Exit. Verify by choosing yes. Down the server from the command prompt. Type exit to return to DOS. Reboot with the new config files to verify their operation. You are now up at the NetWare command prompt and the 'Install' NLM is available for further configuration.
15) At this point the installation varies according to your choices for setting up the server. Follow the on screen directions to complete the install and for adding additional components and features.
NOTE: The current patch level for NetWare 3.12 is required for correct operation. Download all advertised patches and fixes from http://support.novell.com to complete the installation.
Software Product:
Version:
Vendor:
EDOC Number:
Announce Date:
GA Date:
Service End Date:
Program Services:
|
Search Keywords |
| |
|
Document Category |
NetWare | |
|
Date Created |
01-09-98 | |
|
Last Updated |
13-10-98 | |
|
Revision Date |
12-10-99 | |
|
Brand |
IBM PC Server | |
|
Product Family |
PC Server 320 | |
|
Machine Type |
8640 | |
|
Model |
0D0; 0DV; 0X0; 0XT; 0Y0; 0YT; 0YV; 0Z0; 0ZV; 1D0; 1DS; 1YS; 2D0; 2Z0; 3D0; 3Z0; 4D1; 4D2; 4D3; 4D4; 4Y5; 4Y6; 4YF; 4YG; 4YV; 4Z1; 4Z2; 5D1; 5D2; 5Z1; 5Z2; ANW; EE0; EEV; IS2; NNT; NTN; RE0; RE1; RES; REV; SB1; SUN; Z11; Z12; Z13; Z14; Z15; Z16; Z17; Z18; Z19; Z1A; Z1B; Z1C; Z1D; Z1E; Z1F; Z1G; Z1H; Z1J; Z1K; Z1L; Z1M; Z1N; Z1P; Z1Q; Z1R; Z1S | |
|
TypeModel |
| |
|
Retain Tip (if applicable) |
| |
|
Reverse Doclinks |