   |=========================================================================|
   |                                                                         |
   |               Configuring Communications Software: A-D                  |
   |                                                                         |
   |=========================================================================|

    CARBON COPY +

        SatisFAXtion/100:
        Intel's lab tested this software (version 5.0 & 6.0) with the
        SatisFAXtion/100 board, and it is compatible.

        Intel Modems:
        This program is compatible with Intel modems.

        Configuring the Program:
        Here's how to configure Carbon Copy +.

           Run CCINSTAL and choose the communications port for the modem.
            Also set these options as indicated:

            Your Intel Modem             CC+ Modem Choice    Port rate
            ----------------------       ----------------    ---------
            Intel V.42 modems (1)     :   Intel 9600EX          38400
            SatisFAXtion/200          :   Intel 9600EX           9600
            Intel 2400B MNP modems (2):   Intel 2400EX MNP       4800
            Intel non-MNP modems (3)  :   Hayes 2400             2400

        That's all there is to it!


    CLOSE UP

        * Customer report *   Customers report that this program works well
        with the 9600EX and SatisFAXtion modem.  Intel recommends setting
        AUTOBAUD=OFF when using Close Up with Intel V.42 modems (1) or 2400B
        MNP modems (2). You can select AUTOBAUD=ON when using an Intel non-MNP
        modem (3).


    COMPUSERVE INFORMATION MANAGER

        Intel Modems:
        Intel modems are compatible with this program.

        Configuring the Program:
        Here's how to configure Compuserve Information Manager:

           Run Compuserve Information Manager
           Press Alt-P to get to the special screen
           Select "Session Settings" and press <ENTER>
           Fill out all personal information.
            -   Press ALT-B to set the  "BAUD RATE".
                    Intel V.42 modems (1)      :  9600
                    Intel 2400B MNP modems (2) :  4800
                    Intel non-MNP modems (3)   :  2400
            -   Press ALT-C to set the COM.

   ===========================================================================

   June 4, 1992              Intel FaxBACK # 4352                       Page 1
   |=========================================================================|
   |                                                                         |
   |               Configuring Communications Software: A-D                  |
   |                                                                         |
   |============================== (continued) ==============================|

           Press ALT-M to get into the modem setup screen
                Initialize           : ATS0=0 Q0 V1 S12=100^M
                Prefix               : AT
                Reset                :   Z
                Dial Tone            :   DT
                Dial Pulse           :   DP
                Hang up              :   H
                Suffix               : ^M
                Escape               : +++
                Modem acknowledgement: OK
                Connect Message      : CONNECT
                Connect failure      : NO CARRIER
                Logon Parameters     : <leave blank>
                Pause Time           : 10
                Match Time           : 10
           Press ALT-O twice.

        You're done!


    CROSSTALK XVI

        SatisFAXtion/100:
        Intel's lab tested this software (version 3.7) with the
        SatisFAXtion/100 board, and it is compatible.

        Intel Modems:
        This program is compatible with Intel modems.

        Configuring the Program:
        Here's how to configure Crosstalk XVI.

           Start up Crosstalk XVI. At the Status Screen, press <ENTER> to get
            into command mode:
           Set the correct serial port.
            -   Type:  PO x <ENTER>  (where "x" is the serial port that your
                Intel modem is using).
           Enter the appropriate command to set the correct baud rate for your
            modem:
                Intel V.42 modems (1)     : SP 38400
                SatisFAXtion/200          : SP 9600
                Intel 2400B MNP modems (2): SP 4800
                Intel non-MNP modems (3)  : SP 2400

           Set the flow control for your modem

                                             Hardware flow   Software flow
                                             -------------   -------------
                 Intel V.42 Modems (1)     :      ON              OFF
                 Intel 2400B MNP modems (2):      ON              OFF
                 Intel non-MNP modems (3)  :      OFF             ON

            -   To view the Miscellaneous Parameters screen, type: LIT <ENTER>
            -   To turn Software Flow Control OFF, type: FLOW- <ENTER>

   ===========================================================================

   June 4, 1992              Intel FaxBACK # 4352                       Page 2
   |=========================================================================|
   |                                                                         |
   |               Configuring Communications Software: A-D                  |
   |                                                                         |
   |============================== (continued) ==============================|

                To turn Software Flow Control  ON, type: <Ctrl-S>
            -   To turn on Hardware Flow Control, type : HA ON <ENTER>
                To turn off Hardware Flow Control, type: HA OFF <ENTER>

           Go into terminal mode and issue the appropriate command for your
            modem.
            -   Type GO LO <ENTER>
            -   Enter the correct command for your modem.
                Intel V.42 modems (1)     :  AT&F&W <ENTER>
                       Intel 2400B MNP modems (2):  AT&C1&D2\N3\J0\Q3\V1&W
                       <ENTER>
                Intel non-MNP modems (3)  :  AT&C1&D2&W <ENTER>

        You're done!


    CROSSTALK MARK 4

        SatisFAXtion/100:
        Intel's lab tested this software (version 1.01A) with the
        SatisFAXtion/100 board, and it is compatible.

        Intel Modems:
        This program is compatible with Intel modems.

        Configuring the Program:
        Here's how to configure Crosstalk Mark 4.

        With AUTOEXEM enabled, you will see a menu after starting Crosstalk
        Mark 4. Press <ESCAPE> to get to the command prompt. With AUTOEXEM
        disabled, you will immediately see the command prompt.

           Set the serial port.  Type: PORT <ENTER>
            -   Highlight the port on which you installed your modem and press
                <ENTER>.

           Select the correct baud rate for your modem. Type: SPEED <ENTER>
                Intel V.42 modems (1)     : 38400 <ENTER>
                Intel 2400B MNP modems (2):  4800 <ENTER>
                Intel non-MNP modems (3)  :  2400 <ENTER>

           Select flow control for your modem. Type: FLOW <ENTER>
                Intel V.42 modems (1)     : RTS/CTS <ENTER>
                Intel 2400B MNP modems (2): RTS/CTS <ENTER>
                Intel non-MNP modems (3)  : XON/XOFF <ENTER>

           Select "modem init" string in Crosstalk Mark 4.
            -   Type: MODEMINIT <ENTER>
            -   Type: |ATZ|  <ENTER>

           Go into terminal mode and configure the modem.
            -   Type: LOCAL ON <ENTER>
            -   Type: GO <ENTER>
            -   Enter the correct init string for your modem:

   ===========================================================================

   June 4, 1992              Intel FaxBACK # 4352                       Page 3
   |=========================================================================|
   |                                                                         |
   |               Configuring Communications Software: A-D                  |
   |                                                                         |
   |============================== (continued) ==============================|

                Intel V.42 modems (1)     : AT&F&W <ENTER>
                Intel 2400B MNP modems (2): AT&F&C1&D2\N3\J0\Q3\V1&W <ENTER>
                Intel non-MNP modems (3)  : AT&F&C1&D2&W <ENTER>

        You're done!


    DOW JONES 2.03

        Intel Modems:
        This program is compatible with Intel modems.

        Configuring the Program:
        To configure the program, run the MAP program then:

        1.  In the Data Maintenance window, select Setup System.
        2.  Press Y in answer to the question, "Do you want to make any changes
            now?"
        3.  Under Communications Parameters:
            a.  Highlight Com Port and select the port to which the modem is
                attached.  P ress 1 for COM1, 2 for COM2)
            b.  Highlight Modem Type and select the correct modem type for your
                modem:
                    Intel V.42 modems (1)     : press O to select Other.
                    Intel 2400B MNP modems (2): press O to select Other.
                    Intel non-MNP modems (3)  : press H to select Hayes.
            c.  Highlight Baud Rate and press 2 to select 2400.
        4.  If you have a 2400 Baud non-MNP modem, you done.  If you have a
            14.4EX, 9600EX, or 2400 Baud MNP modem, press ESC to configure
            modem command strings.
            a.  Highlight Modem Reset and enter the correct reset string for
                your modem:
                    Intel V.42 modems (1)     : ,+++,AT&F\J1\N0\Q0\V0"H0-J0[13]
                    Intel 2400B MNP modems (2): ,+++,AT&F\J1\N0\Q0\V0[13]
            b.  Press ENTER.  Just press ENTER at the Modem Dial, Acknowledge,
                or Hang up strings to leave them unchanged.


    CROSSTALK FOR WINDOWS V1.1

        When you run Crosstalk for Windows the first time, it offers the option
        to "Run Config". Select "Cancel" to get to the "Crosstalk for Windows"
        screen. After the first time, Crosstalk displays its screen
        immediately. Consult your Windows or Crosstalk manuals if you don't
        know how to "select" an option.

        If you have an Intel V.42 modem (1) or 2400B MNP modem (2), follow
        these instructions:

           Select the "Setup" then select "Device".
            -   Select the "Port" on which you installed your modem.
            -   Select the "Speed" for your modem:
                        Intel V.42 Modems (1)     :  19200
                    Intel 2400B MNP modems (2):  4800

   ===========================================================================

   June 4, 1992              Intel FaxBACK # 4352                       Page 4
   |=========================================================================|
   |                                                                         |
   |               Configuring Communications Software: A-D                  |
   |                                                                         |
   |============================== (continued) ==============================|

            -   Select the "Flow Control" option "RTS/CTS".
            -   Select "OK"

           Select the "Setup" menu then select "Modem".
            -   Select "Custom Modem".
            -   Select "Setting".
            -   Set "Dial Prefix" to:    ATDT
            -   Set "Dial Suffix" to:    ^M
            -   Set "Answer Setup" to:   ATS0=1^M
            -   Set "Initialization" for your modem:
                    Intel V.42 modems (1)     : ^M~ATE0V1X4\J0\N3\Q3\V1^M
                    Intel 2400B MNP modems (2): ^M~ATE0\J0\N3\Q3\V1^M
            -   Set "Disconnect" to:        ~~+++~~ATH0^M
            -   Set "Command OK" to:        OK^M^J
            -   Set "Command Error" to:     ERROR^M^J
            -   Set "No Carrier" to:        NO CARRIER^M^J
            -   Set "Connect" to:           CONNECT^M^J
            -   Set "Connect Speed" to:     CONNECT %^M^J
            -   Set "Connect ARQ" to:       CONNECT %/REL^M^J
            -   Set "Dial Tone" to:         TONE^M^J
            -   Set "No Dial Tone" to:      NO DIALTONE^M^J
            -   Set "Ringing" to:           RING^M^J
            -   Set "Busy" to:              BUSY^M^J
            -   Set "Automatically Select Speed" to:  No (Remove X)
            -   Select "OK"

           Select the "File" menu then select "Save As".
            -   Type:  NORMAL
            -   Select "OK".

        If you have an Intel non-MNP modem (3), follow these instructions:

           Select the "Setup" menu then select "Device".
            -   Select the "Port" on which you installed your modem.
            -   Select the "Speed" option "2400".
            -   Select "OK" (leave other options as they are).

           Select "Setup" menu then select "Modem".
            -   Select "Hayes 2400".
            -   Select "OK".

           Select the "File" menu then select "Save As".
            -   Type:  NORMAL
            -   Select "OK".








   ===========================================================================

   June 4, 1992              Intel FaxBACK # 4352                       Page 5