[ Previous | Next | Contents | Home | Search ]
AIX Versions 3.2 and 4 Asynchronous Communications Guide

Appendix K: 7318 System Errors

The following errors are listed by the module that issues the error. These errors are logged in the AIX error log. Use the AIX command errpt to generate reports from the log.

CS Module Errors

CS Module Errors
Error # Description Resolution
cs001 Text checksum failed. Reboot the 7318 or check the hardware. Possible memory error. Power-cycle 7318. If problem persists, report to technical support.
cs002 Insufficient memory to run operating kernel; rebooting. You do not have enough memory to run this package. Add memory to 7318.
cs003 Operating kernel requires configuration file; rebooting. Verify accessibility of configuration file.
cs004 Power-up selftest was not run. None. This is informational only.
cs005 Incorrect operating image for the hardware. The executable image is not supported on this hardware. Make sure you are booting the executable image for this product.
cs006 Incorrect operating image (P10) for the hardware. The executable image is not supported on this hardware. Make sure you are booting the executable image for this product.
cs007 Invalid operating image (S20) for the hardware. The executable image is not supported on this hadware. Make sure you are booting the executable image for this product.

Exec Module Errors

Exec Module Errors
Error # Description Resolution
exec001 Reboot command issued. None. This is informational only.
exec002 Relogged previous panic. Report log entry from panic to technical support.

HRS Module Errors

HRS Module Errors
Error # Description Resolution
hrs001 Incorrect address type. Change address type in configuration file section.
hrs002 Incorrect interface type. Change interface type in configuration file section.
hrs003 Cannot set primary and backup interface the same. Change one of the interfaces in configuration file section.
hrs004 No reliable server specified. Specify server in configuration file section.
hrs005 Bad reliable server address. Change address in configuration file section.
hrs006 No primary host specified. Define primary host in configuration file section.
hrs007 No backup host specified. Define backup host in configuration file section.
hrs008 Bad primary host address. Change address in configuration file section.
hrs009 Bad backup host address. Change address in configuration file section.
hrs010 Bad backup Internet address. Change address in configuration file section.
hrs011 Bad backup network mask. Change network mask in configuration file section.
hrs012 Cannot specify backup network mask without backup Internet address. Change address in configuration file section.
hrs013 Bad backup gateway address. Change address in configuration file section.
hrs014 Switch from primary to backup interface. None required, informational only.

Kernel Module Errors

Kernel Module Errors
Error # Description Resolution
kernel001 Internal error. Kernel asserted. Try to get an upload and report it to technical support.
kernel002 Bad numeric decode in configuration. Revise the configuration file.

LDT Module Errors

LDT Module Errors
Error # Description Resolution
ldt001 Incorrect configuration file transparent print parameters. Revise configuration file.
ldt002 Incorrect configuration file data in numbered session section. Revise configuration file.
ldt003 Incorrect configuration file data in hot key entry. Revise configuration file hot key definitions.
ldt004 Incorrect configuration file data; too many hot keys. Reduce the number of hot keys defined in configuration file section.

Log Module Errors

Log Module Errors
Error # Description Resolution
log001 Host Message. None required. Informational only.

Session Module Errors

Session Module Errors
Error # Description Resolution
session001 SPX link up. None. This is informational only.
session002 SPX link failed. Verify the host is online and the Ethernet connection is complete.
session003 SPX link down. None. This is informational only.
session004 SPX link down; malformed packet. Report to technical support.
session005 Packet protocol violation. Report to technical support.
session006 Host credit violation on received data. Report to technical support.
session007 Host sending incorrect protocol number in packets. Report to technical support.
session008 Host sending incorrect STREAMS module in open packet. Report to technical support.
session009 Incorrect lan0 address in configuration. Change the address in the IPX configuration file section.
session010 Incorrect lan1 address in configuration. Change the address in the IPX configuration file section.
session011 Incorrect lan2 address in configuration. Change the address in the IPX configuration file section.
session012 Bad framing type specified for SPX/IPX. Change the frametype entry in the IPX configuration file section.

SIO Module Errors

SIO Module Errors
Error # Description Resolution
sio001 Incorrect configuration file entry. Revise the configuration file.
sio002 Unable to set the configuration file value. Revise the configuration file.
sio003 No STREAMS resources. Reduce the number of sessions or services in use.
sio004 Excessive line errors; temporarily disabling port. Verify the data rate, parity, or character size on the port matches the attached device. Improve the physical connection with the shorter cable or slower data rate.
sio005 Power-on self test failed. Power-on the cycle unit and re-verify. If the problem continues, stop using the port or return the Connection Station for repair.
sio006 Requested poll time is below the minimum acceptable value. Change the pollTime value in the port section of the configuration file.

SPX Module Errors

SPX Module Errors
Error # Description Resolution
spx001 SPX link is disconnected in the transmit timeout routine. Check the LAN interface and MAC statistics for Etherenet problems. Check for low memory and reduce the load if neccesary.
spx002 SPX link is disconnected because of a bad sequence number. Report to technical support.
spx003 Interval of 0 is illegal; defaulting. Change the configuration file in the SPX section.
spx004 Transmit retries of 0 is illegal; defaulting. Change the configuration file in the SPX section.
spx005 Receive retries of 0 is illegal; defaulting. Change the configuration file in the SPX section.

[ Previous | Next | Contents | Home | Search ]