How To Clear A Hung tty Port AIX 3.2.x and AIX 4.x

About This Document

For purposes of the following examples, the hung port tty is assumed to be tty0.

1. Determine whether the tty is currently handling any processes:

    
       ps -ef |grep tty0 
   

   For example, the command above would return something like the following:

    
       root  12345    1   0   Aug 29     0     /path/program_name 
   

   The process ID (PID) here is "12345". To kill this process enter:

    
       kill 12345 
   

   The command ps -ef |grep tty0 may be run again to determine whether the process was successfully killed.

   Note: If the process is 'getty', use the following command to kill the process:

    
       pdisable tty0 
   

   In the event the offending process has been successfully killed but the tty is still unresponsive, go to step 2.

2. Type:

    
       fuser -k /dev/tty0 
   

   This will kill any process that can be found running on the port and display the PID (process ID) of that process.

   If the tty is still unusable please continue.

3. Detach and re-attach the cable from the hung port. AIX uses the DCD (Data Carrier Detect) signal to determine the presence of a device attached to the port. By dropping DCD, detaching and re-attaching the cable will in many cases clear hung processes.

   To determine the location of the port on which the tty is configured, use:

    
       lsdev -Cl tty0 
   

   The third column in the output of this command, indicates the address of the tty (e.g., 'S1' below indicates the tty is configured for native serial port 1).

    
       tty0  Available 00-00-S1-00 Asynchronous Terminal 
   

   If the tty is still unusable continue.

4. Flush the port by using stty-cxma:

    
       /usr/lbin/tty/stty-cxma flush tty0 
   

   This command is intended for tty's configured on ports of the 128-port adapter; however, in some cases it can be successfully used to flush other tty ports.

   If the tty is still unusable continue.

5. On the keyboard of the hung terminal press the Q key while holding down the Ctrl key. This will resume any suspended output by sending an Xon character.

   If the tty is still unusable continue.

6. If the unresponsive tty is on an AIX 3.2.x system, skip to step 7. As the AIX 4.x tty subsystem is STREAMS based, one can use strreset to reset the stream (this command does not exist on AIX 3.2.x systems).

   Get the major and minor numbers of the tty by typing:

    
       ls -l /dev/tty0 
   

   The output should look like the following:

    
       crw--w--w-   1 root     system    44,129 Aug 28 13:12 /dev/tty0 
   

   The major and minor numbers are 44 and 129 respectively. To reset this tty type:

    
       /usr/sbin/strreset -M 44 -m 129 
   

   If the tty is still unusable continue.

7. Bring the tty down to a DEFINED state and then make it available. A program will sometimes open a tty port, modify some attributes, and when closing the port, it does not reset those attributes type:

    
       rmdev -l tty0 
   

   This command leaves the information concerning the tty in the database but makes the tty unavailable to the system.

   The following command reactivates the tty making it available to the system.

    
      mkdev -1 tty0 
   

   If the tty is still unusable, consider moving the device (terminal, modem, etc.) to another port and configuring a tty at that location, until the system can be rebooted. If a reboot does not clear the port, a hardware problem is indicated. Check the error report for port hardware problems by typing:

    
       errpt -a |pg